What Type of Paint Should be Used for etrailer Tandem Axle Trailer Fenders w/ Backing Plates

Question

Question:

Is there any specific kind of paint I need to use for the HP32VR fenders?

asked by: Brooke

0

Expert Reply:

You'll want to pick up a paint for the Tandem Axle Trailer Fenders w/ Backing Plates # HP32VR that's designed for steel but that's about it. If you can find a paint that has good corrosion resistance then that would be optimal otherwise you'll have to recoat the fenders on a regular basis to ensure they don't start rusting.

expert reply by: Jon G

0

Answer 1

If the VIN was removed, you do have a couple options. First, check any documentation you received with the trailer, especially if any registration or title/bill of sale type paperwork was included. If there isn't anything like this or there is no…

view full answer...

Answer 2

Travel trailer VIN plates are normally located on the frame at the front of the trailer. It could be on the outboard side or the inboard side of the frame. I have included a picture that shows an example of a VIN plate. Yours will probably look…

view full answer...

Answer 3

You would not want the brakes to lock up the wheels on your trailer. In addition to adjusting the brakes as shown in the video, you will also need to adjust your brake controller. Also, when adjusting and setting the brakes, you will want to do so on…

view full answer...

Answer 4

The wiring that feeds the 12-volt accessory circuit on the 7-way trailer connector is of insufficient gauge to allow enough power to pass through to run a trailer mounted winch. The main function of that circuit would be for lighter-duty…

view full answer...

Answer 5

Replacement of a spindle on a trailer axle is best left to a professional installer. This is not a do-it-yourself type of project. We urge you to use a professional welder experienced in axle fabrication. Proper alignment and welding are critical to…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 8

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 9

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 10

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 11

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 12

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

What Type of Paint Should be Used for etrailer Tandem Axle Trailer Fenders w/ Backing Plates

Product Page this Question was Asked From

Continue Researching