Recommended Hubs And Bearing Kit For A 2004 Triton UT128 Trailer.

Question

Question:

Looking for a hub kit and/or bearing kit for my 2004 Triton UT128 trailer. I can provide a VIN if that helps. The Triton kit is 07995-P. It uses the 1-3/8-inch and 1-1/16-inch bearings and the hub is 5 on 4-1/2". What do you recommend?

asked by: Elliot

0

Expert Reply:

Thanks for the info. This is all 3,500 lb axle standard sizing we are dealing with. If you want a bearing kit you can use part # BK2-100. For a hub you can use part # AKIHUB-545-35-G-EZ-K. The hub does come with all of the bearings, seals, races, grease cap and lug nuts.

We are not able to reference a VIN, but the information you provided is more than enough to tell us what parts you need.

expert reply by: Jesse M

0

Answer 1

According to my research I believe your Triton WCII watersport trailer has 3,500 lb axles and a 5-lug bolt pattern for the wheels, which means the following idler hub should fit: - Easy Grease Trailer Idler Hub Assembly for 3.5K Axles…

view full answer...

Answer 2

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 3

There typically aren't any part numbers stamped onto the trailer spindle that can be used for identification. There are however numbers stamped onto the hub most times which can be used for identification. The TDE46210 tells me you have a…

view full answer...

Answer 4

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 5

The Easy Grease Trailer Idler Hub Assembly for 3.5K Axles part #AKIHUB-545-35-G-EZ-K is a direct replacement for a UFP H-1377.

view full answer...

Answer 6

We have just what you are looking for. I called my contact at TDE and asked about the hub you have on your boat trailer. They told me that it was a 5-stud idler hub for a 3,500-lb axle. That means you need the part #AKIHUB-545-35-K. This is a fit for…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

Yes, the Timken Bearing Kit #TMK52VR will fit your 3,500 lb axle as it fits an standard #84 spindle. The only time this kit won't fit with a 3,500 lb axle is if the trailer/axle is made before the 2000's since that's about the time that…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

The Dexter bearing kit part number K71-717-00 that you referenced is the bearing kit for a number 84 spindle. Our part number for that bearing kit is #BK2-100.

view full answer...

Answer 11

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Answer 12

Hey Roy, The only U-bolt kit we currently only offer for 1-1/2" square axles is part #CE23102, which only has a 3-3/8" length so it likely wouldn't be the best option for you. Instead you'll want to order the 1-1/2" Square…

view full answer...