Are The 1.98" Diameter Bearing Buddies Any Different In Height?

Question

Question:

What’s the shortest barrel length available with a 1.98 dia bearing buddy

asked by: Mike

0

Expert Reply:

All the 1.98" Bearing Buddy Protectors listed below are the same height at just under 2".

Stainless Steel w/ Auto Check # BB1980A-SS
Stainless Steel # BB84SR
Chrome w/ Auto Check # BB1980A
Chrome # BB24SR

expert reply by: Bud M

0

Answer 1

4.80-12 is the tire size you would need as a replacement trailer tire. For that size I would recommend you get the Kenda K353 Bias Trailer Tire - 4.80-12 - Load Range C #AM10062. I attached an FAQ article on trailer tires for you to check out also.

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 6

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

Since both a ST145/R12 size tire, like the Kenda Karrier S-Trail #AM10130, and a 5.30-12 size tire, like the Kenda K353 #AM10068, fit a 12 inch wheel, a ST145/R12 size tire can replace a 5.30-12 size tire. Keep in mind that these tires do have…

view full answer...

Answer 9

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 10

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 11

I have attached a chart you can check out that describes the torque needed per wheel size, wheel stud size and material. For an 8-inch wheel with a 1/2-inch wheel stud the torque is 75 to 86 ft-lbs. For a 15 inch steel wheel with 1/2 inch wheel studs…

view full answer...

Answer 12

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Are The 1.98" Diameter Bearing Buddies Any Different In Height?

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching