Recommended Replacement Jack Legs for a Lippert Ground Control 3.0

Question

Question:

I am looking for three replacement electronic leveling jacks for my 2008 Fleetwood Providence 40X class A diesel pusher RV. The fourth jack was replaced a year ago. Thank you

asked by: David R

0

Expert Reply:

It would depend on what leveling system you have currently, however if you have the Lippert Ground Control 3.0 then you could use:

-The Replacement Front Jack for Lippert Ground Control 3.0 Leveling System # LC362485 for a front jack,

-The Replacement Lead Leg for Lippert Components Ground Control 3.0 Electric Leveling System # LC305340 for a lead leg,

-The Replacement 24-1/2" Left Rear Leg # LC305339 or # LC342610 for a left rear leg,

and the Replacement 24-1/2" Right Rear Leg # LC344792 or # LC428493 for a right rear leg.

If you can let me know specifcally what system you have and which legs you're looking for I'd love to help.

expert reply by: Bryce D

0

Answer 1

Assuming that you have the Lippert Ground Control 3.0 stabilization system you can replace your current rear jacks with the Replacement 22-1/2" Right Rear Leg for Lippert Ground Control 3.0 Electric Leveling System #LC428493 as they will be a…

view full answer...

Answer 2

So it sounds like it is the "passenger's" side of the trailer which would be the right side. That would mean rear leg #LC344792 is the correct replacement for you.

view full answer...

Answer 3

They easiest way I've found to operate the legs of the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System #LC675817 is with the Lippert OneControl monitor if your trailer has it installed. This monitor will allow you to select…

view full answer...

Answer 4

I just checked with Lippert the correct leg you need for the right side middle on the Lippert Ground Control 3.0 item #LC675817 is the Replacement 24-1/2" Right Rear Leg - Lippert Ground Control 3.0 Electric Leveling System item #LC344792 you…

view full answer...

Answer 5

Thank you for the picture with the measurement of your current Lippert Ground Control right rear leg that measures 24-1/2 inches from top to bottom when retracted. Based on that the correct replacement is the part #LC344792 and not the one you…

view full answer...

Answer 6

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 7

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The sure way to pick out replacement landing gear for a trailer that will bolt right up to the current brackets is to measure the distance between the mounting brackets (underside of top bracket to top of lower bracket as shown in the diagram) if it…

view full answer...