U-Bolt Kit For Double-Eye Leaf Spring e48SR

Question

Question:

4-Leaf Double-Eye Spring for 4,000-lb Trailer Axles - 26 Long - Dacromet Item # e48SR need the bolts for the eyes and the ubolt kit for the 4-Leaf Double-Eye Spring for 4,000-lb Trailer Axles - 26 Long - Dacromet # e48SR. Should be the same rust resistant as the leaf please Thanks

asked by: Jude B

0

Expert Reply:

Here is what you need for a rust-resistant U-bolt kit and shackle bolts to go with the 4-Leaf Double-Eye Spring # e48SR:

- CE Smith U-Bolt Kit for Mounting 3,500-lb, Round Trailer Axles - 5-1/2" Long U-Bolts - Zinc # CE23002

- Zinc Shackle Bolt with Locknut for Double-Eye Springs - 3" Long # TRFA73Z916DLNZ

expert reply by: Kyle S

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 3

The spring hanger placement is going to be determined by your axle spacing. For example, if your axles are spaced 33 inches apart, as shown in the attached diagram, a 7K axle slipper spring, like #e74SR, requires a distance of 28-1/2 inches between…

view full answer...

Answer 4

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 5

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but they…

view full answer...

Answer 10

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 11

I attached a picture that shows the proper position of shackles and equalizers on trailer suspension. Sometimes the shackle will flip up but if you jack up the trailer by the axle that's got the shackle flipped you can usually get it to flip back…

view full answer...

Answer 12

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...