4-Way Trailer Wiring Harness For 2024 Chrysler Pacifica

Question

Question:

is there a 4-way trailer wiring harness for my 2024 Chrysler Pacifica?

asked by: Eli

0

Expert Reply:

There is indeed a 4-way trailer wiring harness for your 2024 Chrysler Pacifica, made by Curt. The correct part number is the following:

- Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector # C47VV

expert reply by: Kyle S

0

Answer 1

I recommend installing the etrailer Trailer Hitch Receiver #e98903 on your 2024 Chrysler Pacifica. This has the larger 2" receiver opening which will allow you to carry the Yakima StageTwo Bike Rack for 4 Bikes #Y85AR. This is going to be the…

view full answer...

Answer 2

The Hidden Hitch by Draw-Tite Trailer Hitch Receiver #DT46GR is the most concealed option for your 2023 Chrysler Pacifica. This allows you to remove the 2" receiver when not needed so you will not see any portion of the receiver below your rear…

view full answer...

Answer 3

When the etrailer hitch part #e98903 was installed here we found that it measured 5 inches from the center of the hitch pin hole out to the rear bumper edge. Since that's not enough clearance for the Inno #INH540 and none of our other hitches…

view full answer...

Answer 4

Both the Draw-Tite Class III Trailer Hitch #76046 and the Curt Class III #C13383, which are confirmed to fit your 2018 Chrysler Pacifica, will require that the heat shield is trimmed/modified for proper installation. In both cases the heat shield…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

As far as wiring for the 2024 Toyota Grand Highlander, we do have the Curt #C59236 available which is more of a universal hardwire harness. Unfortunately there are not any plug-and-play options that have been confirmed to fit as of yet (October 4,…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 12

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...