Is Capacity of Dexter E-Z Flex Suspension Kit # K71-652-00 Per Axle or As a Pair

Question

Question:

On Dexter part #K71-652-00 it says it for 6000# axle. Is that for each axle or total weight for both axles? my axle are 3500# each. total trailer weight is 6400# thanks.

asked by: Dennis R

0

Expert Reply:

Great question. So the Dexter E-Z Flex Suspension Kit # K71-652-00 is for use with tandem axles that each have a capacity of up to 6,000 lbs. So total the trailer could have a capacity of up to 12k.

expert reply by: Jameson C

0

Answer 1

The Equa-Flex Cushioned Equalizers #LC145546 that includes the 4 wet bolts has greaseable pivot points. This means you can replace the lower bolts that hold the pivot arms in place and replace them with the 4 wet bolts. This kit is rated for 5,000lb…

view full answer...

Answer 2

Your drawing picture with the dimensions of your equalizer did not make it through but since I can identify the equalizer you have as the part #TREQE1 from the picture that did make it through the best cushioned equalizer we offer that will be a…

view full answer...

Answer 3

The distance from the center of the uppermost bolt hole where it attaches to the leaf spring hanger to the center of the two bolt holes which attach to the left springs on the Equa-Flex Cushioned Equalizers part #LC279688 is 4". If this distance…

view full answer...

Answer 4

Cushioned trailer suspension equalizers like the Lippert Equa-Flex #LC279688 are chosen based on both their mounting hole spacing and their axle weight rating compatibility. The dimensions of this equalizer are noted in the linked photo and these…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but they…

view full answer...

Answer 7

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 8

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 9

The spring hanger placement is going to be determined by your axle spacing. For example, if your axles are spaced 33 inches apart, as shown in the attached diagram, a 7K axle slipper spring, like #e74SR, requires a distance of 28-1/2 inches between…

view full answer...

Answer 10

Yes, axle spread and wheel base by definition are the same measurements. You will measure from the center of one axle to the center of the 2nd axle to determine what you axle spread is. This may be difficult as some wheels and covers will make this…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...