Does Roadmaster Sway Bar # RM-1139-179 Come with End Links

Question

Question:

I cant seem to find the end links for sway bar 1139-179. Its going on an e450 super duty 2016 class c

asked by: Jeff D

0

Expert Reply:

Due to how the Roadmaster Sway Bar part # RM-1139-179 installs it does not come with end links. It basically just comes with the bar, bushings, and bushing clamps. This sway bar is designed to be installed using the factory end links that are already present on the vehicle.

expert reply by: Jameson C

0

Answer 1

What vehicle are you needing this for? It looks like you have a 2019 Ford E-Series in our fitguide but if you could let me know if it's an E-350 or E-450 and whether you have a Class A motorhome, Class C motorhome, or an Emergency Vehicle I can…

view full answer...

Answer 2

When installing the end link kit part #RO57FR you do sometimes need to use a 1/2 inch drill bit to enlarge the holes on the sway bar. You do need to make sure you are using a drill bit designed for metal and not softer materials as they won't…

view full answer...

Answer 3

If there isn't a way to access it from the inner side of the frame or from the side then it would have a weld nut in frame and you would be able to just remove the bolt normally. There unfortunately isn't a guide that shows if there's a…

view full answer...

Answer 4

Yes, the Roadmaster Reflex Steering Stabilizer part #RM47MR does fit the 2018 E350 Winnebago Minnie Winnie Motorhome you mentioned.

view full answer...

Answer 5

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 6

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 7

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 8

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 9

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 10

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Does Roadmaster Sway Bar # RM-1139-179 Come with End Links

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching