Replacement Front Jack For Ground Control 3.0 on Grand Design 5th Wheel

Question

Question:

I Have a Grand Design Refection 310RLS 5th wheel that needs a Landing Leg Replacement on Drivers side. Can You verify for me if the LC362485 is the replacement I need for my RV.

asked by: Jim R

0

Expert Reply:

I can indeed; the correct replacement for the front jack of the Ground Control 3.0 on your Grand Design Reflection is the part number you referenced:

- Replacement Front Jack for Lippert Ground Control 3.0 Leveling System # LC362485

expert reply by: Kyle S

0

Answer 1

For the Lippert Ground Control 3.0 Trailer Leveling System #LC358590 we do offer the front leg only with part #LC362485.

view full answer...

Answer 2

I recommend first checking your battery charge and output. These controllers are finicky and want to see 12V constant. If possible have your camper plugged in or vehicle plugged in and running when using the controller. You will also want to double…

view full answer...

Answer 3

Yes, we do have replacement parts available. If I am following you correctly, you are looking for the replacement lead leg for your Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System, #LC675817. This will be part number, #LC305340.

view full answer...

Answer 4

The "Out of Stroke" error on the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System - 4-Point Set #LC358590 and 6-Point Set #LC675817 means that they have reached the max height, can no longer lift so you need to relocate your…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Replacement Front Jack For Ground Control 3.0 on Grand Design 5th Wheel

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching