Correct Replacement Master Cylinder and Shock for a Dexter Model A60/A75/XR84 Brake Actuator

Question

Question:

Good morning, I have a dual axle boat trailer with disk brakes. The Brake Actuator says Model A60/A75/XR84 UFP I believe it is a A75 it has the standard ball end that hooks on to the vehicle 2 ball. It looks like i need a new master cylinder and a new shock. The master has a solenoid attached with a blue wire. what would the part numbers be? Thanks

asked by: Brad P

0

Expert Reply:

For a replacement shock you're going to want the Replacement Shock Absorber Spring Kit for Dexter Brake Actuators # TK71-758-00, and for the replacement master cylinder you'll just need the Replacement Master Cylinder Assembly for Dexter Brake Actuators # DX44FR and you'll be all set.

expert reply by: Bryce D

0

Answer 1

The Replacement Shock Absorber Spring Kit #TK71-758-00 is the correct shock for your UFP Surge Brake Actuator. The picture you included does not specify if it is for a disc or drum brake set, so I have found both for you to choose from. Disc Brake…

view full answer...

Answer 2

It sounds like you have a couple wires run backwards on your Lippert powered steps. Its hard to say exactly which wires are wrong but most likely a power wire and ground is backwards. The best recommendation I can give would be for you to go over the…

view full answer...

Answer 3

The Replacement Master Cylinder Assembly for Dexter Brake Actuators - Disc Brakes #DX44FR can be used to replace the A-60 master cylinder and is designed to fit on a variety of Dexter/UFP brake actuators.

view full answer...

Answer 4

Your old unit may have been self grounding if it only had the blue wire for the reverse light circuit, but the Replacement Master Cylinder Assembly for Dexter Brake Actuators - Disc Brakes #DX44FR does have an independent ground wire that will need…

view full answer...

Answer 5

Yes, the Titan shock part #TK71-758-00 is the correct replacement for the UFP A-60 you have on your trailer currently.

view full answer...

Answer 6

We do have the correct replacement controller for the Kwikee 1800709 you have. What you need is the Replacement Control Unit #LC363989.

view full answer...

Answer 7

Thanks for the photos. It is clear you have a Titan brake actuator like the Brake Actuator with Manual Lockout - Bolt On - Drum - 2" Ball - 7,500 lbs #T63FR. It sounds like you need the Replacement Master Cylinder Assembly for Titan/UFP Brake…

view full answer...

Answer 8

Judging from the photo, it does look like the #DX44FR that you were looking at is the correct replacement part you need. This is the replacement master cylinder for the A-60, A-75, A-84, A-160, A-200, XR-84 and XR-200 series of Dexter actuators, in…

view full answer...

Answer 9

The electric lockout doesn't do anything to the actuator itself, it is a solenoid that doesn't let the fluid pressurize to case the wheel cylinder or brake caliper to engage. The coupler not returning to the forward location has more to do…

view full answer...

Answer 10

You must have an older model 60 actuator because the new ones and replacement master cylinders do not have the bypass port that you mentioned. So what you would do is use the master cylinder you have purchased and also replace the solenoid with…

view full answer...

Answer 11

It is not recommend to jack up a trailer by the axle. This may cause damage to the axle itself. It also puts too much stress on the leaf springs. Instead, you will want to place the jack under part of the trailer frame preferably next to the leaf…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Correct Replacement Master Cylinder and Shock for a Dexter Model A60/A75/XR84 Brake Actuator

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching