Crossbar Channel Cover that Can Fit Opening that is .45 of an Inch

Question

Question:

I have a set of cheap universal crossbars on my van. There is a channel running underneath the extruded aluminum bars measuring 0.45” in width. I am looking for some rubber molding t-molding? in an attempt to reduce wind noise. I have pics if needed. Any help appreciated.

asked by: Robert S

1

Helpful Expert Reply:

The Thule crossbar strip cover part # TH853354407 would work to cover your opening that is .45 inches wide. That is the diameter opening it was designed to fit.

expert reply by: Jameson C

1

Answer 1

You likely have the Thule Aero load bars which take rubber strip #TH853354407 for 53 inches.

view full answer...

Answer 2

I may have a solution for you. The Replacement Rubber Strip #TH853354407 is designed to fit into a channel that is 7/16 of an inch wide on the top and 7/8 of an inch wide at the bottom. I have included a diagram that shows these measurements. You…

view full answer...

Answer 3

The Thule Replacement Rubber Strip #TH853354407 referenced in your question is designed to fit the Thule Aero Load Bars. To see if they might fit the channel on your Brightlines Crossbar, you will want to take a couple measurements. This particular…

view full answer...

Answer 4

You can install the Prodigy P3 part #90195 in your 2017 Audi Q7 but you will need some wiring that you can only get at an Audi dealer. the brake control harness: (qty. 1) #1J0-972-782 housing and (qty. 2) #000-979-228 wire/terminal assemblies.…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 9

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 10

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 11

Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…

view full answer...

Answer 12

The squeaking noise on your trailer is probably coming from the joints in the suspension creating metal to metal friction. So, unless your original Equa-Flex Cusioned Equalizers are damaged or corroded, what will make the biggest difference is to…

view full answer...

Crossbar Channel Cover that Can Fit Opening that is .45 of an Inch

Product Page this Question was Asked From

Continue Researching