Front Mounted Hitch for a 1999 Dodge RAM 2500 Diesel

Question

Question:

Does the 31604 front mount hitch receiver mount fit the 1999 Dodge RAM 2500 Diesel with 4 wheel drive?

asked by: Sergei

0

Expert Reply:

Curt Front-Mounted Hitch, part # 31604 works for most versions of the 1999 Dodge Ram. It fits all models of the 1999 Dodge Ram as long as it is not the Sport model.

expert reply by: Andi

0

Answer 1

The Curt #31604 fits all models of the 1999 Dodge Ram 2500 with the exception of the Sport. As long as your truck is not the Sport model you will be able to install this on the front.

view full answer...

Answer 2

Yes, cutting the bumper will allow you to install the Curt #31604 on your 1999 Dodge Ram 2500 Sport. The bumper is the only difference between this and other models so you will be able to bolt it onto the frame. It won't look pretty, but…

view full answer...

Answer 3

I spoke to my contact at Curt and she confirmed that the Curt Hitch part #31604 that you referenced would fit your 2002 Dodge Ram 2500 Sport. There will be fascia trimming since you have a Sport model. You can see more info on that in the install…

view full answer...

Answer 4

I spoke to my contact at Curt and she confirmed that the Curt Front Hitch part #31604 that you referenced would fit your 2002 Dodge Ram 2500 Sport.

view full answer...

Answer 5

Are the bolts you're referring to in the same hole the hitch uses for its front fasteners? Sometimes they will be there from the factory but not always. If this is what you're referring to then yes they need to be removed to install the front…

view full answer...

Answer 6

All the hardware necessary for installation, nuts, bolts, and washers, are included with the hitch. We have not yet done an install with this particular front mount hitch, so we do not have any photos. According to the instructions, the front air dam…

view full answer...

Answer 7

You could use Curt front hitch #31604 for your 2000 Dodge Ram. The #31604 hitch installs under the front fascia and attaches to parts of the truck frame that are not used by the factory tow hooks so you will not have to remove them. I have linked…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Personally I wouldn't go with Timbren's for your needs. They're essentially rubber bump stops that prevent your suspension from flexing when weights placed on the rear of your Canyon. The major issue with them is comfortability when you…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

You are on the right track. The only way we have that will allow you to use the Thule T2 Pro Xtr Bike Platform Rack part #TH69TX with the 2.5" receiver tube opening on your truck would be with adapter. For this, I recommend the Brophy Hitch…

view full answer...

Front Mounted Hitch for a 1999 Dodge RAM 2500 Diesel

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching