Can Dexter 6 Lug Hub/Drum be Replaced with Standard Hub

Question

Question:

I have a boat trailer that has 2 Dexter Brake Drum Hubs on it that I need to replace. I no longer have Brakes on this trailer so I need to know if I can replace the Drum Hubs with regular 6 on 5 1/2 Trailer Hubs.

asked by: Danny S

0

Expert Reply:

Yes, there are hubs that can replace your Dexter hub/drums that you have currently. If the axle is rated for 6,000 or 5,200 lb you would want the hub part # AKIHUB-655-6-EZ-K or if it's rated for 3,500 lb you'd want the # AKIHUB-655-35-EZ-K.

expert reply by: Jameson C

0

Answer 1

Thanks for the information on your trailer. For your axle with brakes I recommend the Trailer Hub and Drum Assembly - 5,200-lb and 6,000-lb E-Z Lube Axles - 12" - 6 on 5-1/2 #AKHD-655-6-EZ-K if you have the spindles with the integrated grease…

view full answer...

Answer 2

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 3

To determine if there are compatible hubs and associated bearings to replace your current hubs to a more standard size you will have to take several precise measurements on the spindle of your axle. It is recommended to use a set of dial calipers to…

view full answer...

Answer 4

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hello Brian, we do offer some parts that will work for your application and will be very similar to the BPH1206EPR kit that you mentioned. Like you said, the 12 x 2-1/2 drums are pretty uncommon, so I would have to recommend going instead with the…

view full answer...

Answer 7

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Answer 8

There typically aren't any part numbers stamped onto the trailer spindle that can be used for identification. There are however numbers stamped onto the hub most times which can be used for identification. The TDE46210 tells me you have a 3,500…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...