Will The Dexstar Conventional Steel Wheel # AM20334 Allow For Hubcaps?

Question

Question:

Are these rims cable of putting hubcaps on?

asked by: Steve N

0

Expert Reply:

The Dexstar Conventional Steel Wheel # AM20334 is designed to be used with a Baby Moon Trailer Wheel Center Cap # AM90086. The profile which allows for the baby moon center cap does not typically allow for a standard wheel hubcap to fit.

expert reply by: Bud M

0

Answer 1

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 4

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 5

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 6

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Answer 7

The 12 inch tires that we carry are rated for 65 miles per hour. Any faster than that for extended periods and the excessive heat build up will cause tire failure. To get a tire with a higher speed rating you would have to go up in size. That also…

view full answer...

Answer 8

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 9

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 10

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 11

The modern size equivalent of the 20.5x8-10 that you have currently would be the same size tire that is on the #AM3H340 that you referenced, 205/65-10. As long as the bolt pattern of your current hubs are 4 on 4 inch the wheels of this would bolt up…

view full answer...

Answer 12

Good morning, Cliff. As of today (3/27/24) we are expecting the #KE33JR tire/wheel combo to be in stock in about 2 weeks. Hopefully this means we can take our own pictures and put them on the site within maybe about 3-4 weeks from now. What I can…

view full answer...

Will The Dexstar Conventional Steel Wheel # AM20334 Allow For Hubcaps?

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching