Grease Cap For 1.95 Inch Trailer Hub Bore

Question

Question:

The ID of my trailers hub is 1.95. Which dust cap would fit?

asked by: Guenthet

0

Expert Reply:

The correct grease/dust cap for a 1.95 inch trailer hub bore is the following:

- Grease Cap # TRAG-DC-196

This has a flange diameter of 1.957 inches which is exactly what you'll need as they are meant to be ever so slightly larger for a tight fit as this is a drive-in cap.

expert reply by: Kyle S

0

Answer 1

The closest fit of any bearing protector we have to a 1.950 hub bore is going to be either #BB1968SS for stainless steel or #BB1968 for chrome plated. These are designed to fit a hub bore of 1.968 inches. Bearing protectors are often slightly…

view full answer...

Answer 2

I can help you with determining the correct replacement wheel and tires for your trailer with a 6.90-9 tire. Normally you would just need to measure the diameter of the wheel to get the size, but we know a 6.90-9 tire fits a 9" x…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

The 12 inch tires that we carry are rated for 65 miles per hour. Any faster than that for extended periods and the excessive heat build up will cause tire failure. To get a tire with a higher speed rating you would have to go up in size. That also…

view full answer...

Answer 8

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 9

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 10

Hey Jim! The Taskmaster and Westlake tires, like the Taskmaster ST235/75R15 Off-Road #TA45RR and Westlake ST235/75R15 Off-Road #WST54FR you were looking at, are made in China. A lot of people tend to shy away from trailer tires made in China but…

view full answer...

Answer 11

Good morning, Cliff. As of today (3/27/24) we are expecting the #KE33JR tire/wheel combo to be in stock in about 2 weeks. Hopefully this means we can take our own pictures and put them on the site within maybe about 3-4 weeks from now. What I can…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Grease Cap For 1.95 Inch Trailer Hub Bore

Product Page this Question was Asked From

Continue Researching