Parts Needed to Add a 7-Way Connector to a 2007 Range Rover

Question

Question:

2007 Range Rover I need a 7 pin connector so I can have trailer brakes as well as lights

asked by: Robert

0

Expert Reply:

I checked with our vendors and there are no custom fit wiring harnesses available for the 2007 Range Rover. This means to add a 7-way connector you will need to install both a 4-way and 7-way.

The first harness you will need is the Upgraded Modulite Vehicle Wiring Harness Kit item # 119147KIT. This is a universal harness that you will need to splice into your Range Rover's wiring. It will provide you with a 4-way connector.

The second harness you will need is the Universal Installation Kit for Trailer Brake Controller item # ETBC7. The kit includes a pre-wired 7- and 4-way trailer connector that mounts easily at the rear of your Range Rover with an included bracket. This kit is designed for use on a vehicle with an existing 4-way flat trailer connector and plugs directly into it.

You will then connect the blue wire to the blue wire on the brake controller, connect the black wire to the positive post on the vehicle's battery, the white wire to ground, and the yellow wire to vehicle's reverse circuit if applicable. This will provide you with the ability to control your trailer's brakes and also provide you with a 12v power wire for you trailer's accessory lights.

To operate your trailer's brakes you will also need a brake controller, I recommend the Redarc Tow-Pro Liberty Brake Controller item # RED24FR and the item # RED69FR wiring harness.

expert reply by: Jerred H

0

Answer 1

This can be caused by a few things, but as you have enough slack in the wire, it is most likely just one of two things. The door flap, for the lack of a better way to put it, on the 7 Way plug on the towing vehicle snaps down on a tab on the 7 Way…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 4

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 7

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Answer 8

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 9

There are a number of factors involved when converting a semi 7-way to an RV 7-way. Semis generally use a 7-pin round pin socket, similar to #PK11720. And RV style 7-way uses blades, like #PK12706. We do not offer any pre-made adapters to make this…

view full answer...

Answer 10

I do have a solution for your 2024 Kia Telluride that has the LED taillights that does allow it to have both a 4-way and 7-way plus install a brake controller but it is not with the #TK74CR which does not work for you based on the LED taillights.…

view full answer...

Answer 11

Either way is correct. It depends on if you want to keep the semi-style 7-Way (if you need to tow that type of trailer) or if you will never be towing a semi-trailer. If you need to keep the 7-Way semi active on the truck, then you would need to make…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...