Ball Mount With Extra Long Shank Needed For 2014 Subaru Forester
Question:
I need 4.5-5.5inch rise, 2inch class III, preferably with a hollow stinger so I can use a Softride anti-rattle . The tough part is that I have a 2014 Subaru Forester with Curt hitch, where the center of the pin is fully 7inch forward of the rear of the bumper. I am looking for something like the Hidden Hitch 80240, but I fear that the angle support piece would not clear my bumper. I could always order and see, but if you can advice on a choice I would appreciate this. I will include a picture of a short 2inch stinger installed that itself cant be use flipped because it sits too close to the bumper. sorry for poor focus
asked by: David H
Expert Reply:
I did some research for your 2014 Subaru Forester and the clearance you need to clear your rear bumper.
I recommend the Curt Ball Mount, part # D-28. This ball mount has an extra long hollow shank and features a 4 inch rise or a 6 inch drop. The distance from the center of the hitch pin hole to the closest point of rise is 8-1/4 inches so that should give you sufficient clearance for your vehicle. I have attached a photo that shows the dimensions of the # D-28 ball mount.
Per Curt warranty requirements, all non-trailer loads, like bike racks, or cargo carriers must be supported by stabilizing straps, like part # 18050.
Products Referenced in This Question
Curt Cam Buckle Stabilizing Strap for Hitch-Mounted Accessories - 61" x 1" - Qty 1
- Accessories and Parts
- Hitch Bike Racks
- Hitch Cargo Carrier
- Tie Down Straps
- CURT
more information >
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 14-1/4" Long - 6,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 6 Inch
- Rise - 4 Inch
- Fits 2 Inch Hitch
- 6000 lbs GTW
- Class III
- Long Shank
- CURT
more information >
Product Page this Question was Asked From
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 14-1/4" Long - 6,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 6 Inch
- Rise - 4 Inch
- Fits 2 Inch Hitch
- 6000 lbs GTW
- Class III
- Long Shank
- CURT
more information >
Continue Researching
- Shop: Curt Ball Mount for 2" Hitches - 8" Rise, 9-1/4" Drop - 14" Long - 5K
- Q&A: Recommended Ball Mount for 8 Inch Drop and 7,500 to 10,000 Capacity
- Shop: Trailer Hitch
- Shop: etrailer Hitch Receiver Lock for 2" and 2-1/2" Hitches - Flush - 3-5/8" Span - Chrome
- Search Results: hitch lock
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Video: Lets Go Aero Anti-Rattle Hitch Receiver Lock Review
- Article: How to Measure for Trailer Hitch Drop
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Shop: Trailer Wiring
- Shop: Anti-Rattle Trailer Hitch Receiver Lock for 2" Hitches - 3-1/2" Span
- Search Results: locking hitch pin
- Article: The 5 Best Trailer Drop Hitches You Can Buy
- Search Results: hitch pin
- Shop: etrailer Trailer Hitch Receiver Lock for 2" Hitch - Flush - 2-5/8" Span - Stainless Steel
- Q&A: Does Truck with 6-1/2 ft bed Have to Use Slider Hitch for Turning Clearance with Fifth Wheel Hitch
- Shop: Suspension Enhancement
- Article: How to Choose the Right Trailer Hitch Class
- Search Results: coupler lock
- Article: Trailer Wiring Diagrams
- Shop: Brake Controller
- Q&A: Parts Needed to Flat Tow 2024 Ram 1500 Behind Motorhome With Roadmaster Tow Bar
- Shop: etrailer Hitch Pin Alignment Collar for Hitch Accessories - 2" Hitches
- Search Results: hitch
- Q&A: Can a Trailer Ride With the Tongue at an Upward or Downward Angle
- Shop: Roof Rack
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: etrailer.com Flat Lip Trailer Coupler Lock Review
- Shop: Base Plate for Tow Bar
- Shop: etrailer Trailer Hitch Receiver Lock for 2" Hitches - Flush - 2-5/8" Span - Chrome
on Trailer Hitch Ball Mount
