Dexter Heavy Duty Equalizer Suspension Kit for Trailer with 34 inch Wheelbase

Question

Question:

I have a tandem trailer that is 34 between axels. Looking for a suspension kit for tandem axel trailer. What do you recommend for this type of trailer? The leaf springs are 1 3/4 and center hanger is 4 1/2.

asked by: Dana

0

Expert Reply:

Your trailer's wheelbase is a dimension that is compatible with the Dexter Heavy Duty Suspension kit part # K71-359-00 that you referenced so this would be a great option. The equalizers are a little wider than what you have but the shackle length of what comes with this kit would compensate for that.

expert reply by: Jameson C

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have…

view full answer...

Answer 3

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is…

view full answer...

Answer 4

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but…

view full answer...

Answer 5

I have attached for you below some common torque values needed for a trailer suspension system but a lot of these will vary by bolt size and other factors. U-Bolts: Varies by Size - 1/2" bolts: 45 ft/lbs - 70 ft/lbs, 9/16" bolts: 65…

view full answer...

Answer 6

Yes, axle spread and wheel base by definition are the same measurements. You will measure from the center of one axle to the center of the 2nd axle to determine what you axle spread is. This may be difficult as some wheels and covers will make this…

view full answer...

Answer 7

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 8

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 9

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 10

The standard diameter for trailer leaf spring bolts is 9/16 inch which is why the part #E4139 and all similar options have this hole size. We don't have anything with a smaller diameter but my guess is what you have is actually 9/16 inch.

view full answer...

Answer 11

When replacing shackle straps they should be the same length as the ones that were previously on your tandem axle trailer; replacing them with longer straps will result in additional play in your trailer suspension which could lead to additional wear…

view full answer...

Answer 12

The spring hanger placement is going to be determined by your axle spacing. For example, if your axles are spaced 33 inches apart, as shown in the attached diagram, a 7K axle slipper spring, like #e74SR, requires a distance of 28-1/2 inches between…

view full answer...

Dexter Heavy Duty Equalizer Suspension Kit for Trailer with 34 inch Wheelbase

Product Page this Question was Asked From

Continue Researching