Could Rhino Rack Aero Bar Roof Rack for Camper Shells Attach to Truck Bed Rails

Question

Question:

Can you mount this to pickup bed rail caps?

asked by: Wesley F

0

Expert Reply:

As long as you're okay with drilling holes into the top of your bed rails yes you could mount the Rhino-Rack Aero Bar Roof Rack for Camper Shells # Y02-480B to the top of your truck bed rails.

expert reply by: Jameson C

0

Answer 1

It is likely the Thule Xsporter Pro Low Truck Bed Rack #TH24QC will fit your 2001 Dodge Ram 1500, but it is not a custom-fit rack so there is no fit information on any specific truck. That said, all you need to have is the bed rails exposed for it…

view full answer...

Answer 2

The Thule Track Mount Roof Racks are all going to be limited to 165 lbs therefore this will give you a good idea of how much weight can be carried. However, the camper top manufacturer may have a lower weight capacity figure so if that is the case…

view full answer...

Answer 3

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Tracks can absolutely be installed on the roof of your A.R.E. Truck Cap to provide a mounting system for a roof rack. For this I recommend the Yakima Tracks, which come in 42 inch #Y01126, 54 inch #Y01127, and 60 inch #Y01135 lengths. These tracks…

view full answer...

Answer 6

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 7

The Rhino-Rack Heavy-Duty Roof Rack Roof Rack have specific C-channels that are designed to fit specific Rhino-Rack Heavy-Duty accessories, like the Rhino-Rack Hi-Lift Jack and Shovel-Holder Brackets #RRRCB-RSHB-RJHB as an example. That's…

view full answer...

Answer 8

For a roof rack to be compatible on your 2020 Jeep Wrangler with Sky One-Touch Power Top, it can't be mounted on the top of the roof and it needs to be high enough for the folding roof to clear. What you need are tall gutter-mounted roof…

view full answer...

Answer 9

Yakima's Skyline towers part #Y53TR can fit the tracks of the Retrax XR that you have with the landing pad 1 part #Y00221 but there isn't a way with the Baseline towers. Your Yakima Corebar or Jetstream bars will work with the Skyline…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Thanks for reaching out, Joe! I recommend using the Rhino-Rack Aero Bar Roof Rack for Camper Shells #Y02-480B which comes with 63" long tracks as well as 54" long crossbars which should give you a little bit of overhang on your…

view full answer...

Answer 12

According to Rhino Rack, if you were to go with the shorter bars, you'll only have 1-1/4 inch of leeway on each side which isn't enough in their opinion. I'd recommend going with the 71 inch bars so you'll be certain…

view full answer...