How to Know if Thule Xsporter Pro Low Truck Bed Rack Will Fit Truck

Question

Question:

Will this fit my 2001 Dodge Ram 1500 Regular Cab? Thule Xsporter Pro Low Truck Bed Rack - Full Size - 220 lbs

asked by: Peter R

0

Expert Reply:

It is likely the Thule Xsporter Pro Low Truck Bed Rack # TH24QC will fit your 2001 Dodge Ram 1500, but it is not a custom-fit rack so there is no fit information on any specific truck. That said, all you need to have is the bed rails exposed for it to clamp onto, as in the accompanying photo. If you have that, then you can use the Xsporter Pro Low Bed Rack # TH24QC.

expert reply by: Kyle S

0

Bed Rails Needed to Attach Thule Xsporter Pro Low Truck Bed Rack
(click to enlarge)

Answer 1

As long as you're okay with drilling holes into the top of your bed rails yes you could mount the Rhino-Rack Aero Bar Roof Rack for Camper Shells #Y02-480B to the top of your truck bed rails.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 4

Tracks can absolutely be installed on the roof of your A.R.E. Truck Cap to provide a mounting system for a roof rack. For this I recommend the Yakima Tracks, which come in 42 inch #Y01126, 54 inch #Y01127, and 60 inch #Y01135 lengths. These tracks…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

The Rhino-Rack Heavy-Duty Roof Rack Roof Rack have specific C-channels that are designed to fit specific Rhino-Rack Heavy-Duty accessories, like the Rhino-Rack Hi-Lift Jack and Shovel-Holder Brackets #RRRCB-RSHB-RJHB as an example. That's the…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Yakima's Skyline towers part #Y53TR can fit the tracks of the Retrax XR that you have with the landing pad 1 part #Y00221 but there isn't a way with the Baseline towers. Your Yakima Corebar or Jetstream bars will work with the Skyline towers…

view full answer...

Answer 10

Thanks for reaching out, Joe! I recommend using the Rhino-Rack Aero Bar Roof Rack for Camper Shells #Y02-480B which comes with 63" long tracks as well as 54" long crossbars which should give you a little bit of overhang on your canopy. Per…

view full answer...

Answer 11

According to Rhino Rack, if you were to go with the shorter bars, you'll only have 1-1/4 inch of leeway on each side which isn't enough in their opinion. I'd recommend going with the 71 inch bars so you'll be certain of a good fit. As…

view full answer...

Answer 12

For your setup I recommend the TrackTowers for Yakima Crossbars and Platforms - Track Mount #Y52AV which includes everything you need to mount Yakima crossbars to your Retrax cover (unless you plan on using the Round or HD bars - then you'll need…

view full answer...