Replacement Side Rail Endcaps for a TruXedo LoPro Tonneau Cover On a 2014 Ford F-150

Question

Question:

I have a TonneauTrax, part #598195, Ser # 015043103, on a 2014 Ford F150. I need a set of Cargo Rail End Plugs. In the literature that came with it, this is Item 27, part # 1117470. I cant find them. Can you please help me?

asked by: Ronald M

0

Expert Reply:

I went ahead and checked out your tonneau, and it looks like you have a LoPro so you could just use the Replacement Side Rail Endcaps for TruXedo LoPro Tonneau Covers # TX28TV as these will fit all LoPro tonneau covers.

expert reply by: Bryce D

0

Answer 1

For your TruXedo Lo Pro Soft Roll-up Tonneau Cover #TX567101 (NLA) on your 2014 Ford F-150, the correct end caps are the Replacement Front Header End Plugs for TruXedo LoPro Tonneau Covers #TX1117540 that you mention.

view full answer...

Answer 2

The TruXedo Side Rails 1113645 were used on a few different tonneau covers with the TruXedo Lo Pro QT Soft Roll-up Tonneau Cover being the most popular. Therefore, the Replacement Side Rail End Caps With Seals for Truxedo LoPro Tonneau Covers part…

view full answer...

Answer 3

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 4

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 5

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 8

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Answer 9

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 12

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Replacement Side Rail Endcaps for a TruXedo LoPro Tonneau Cover On a 2014 Ford F-150

Product Page this Question was Asked From

Continue Researching