Capacity of Shocker Hitch XRC Ball Mount With 2-5/16" Hitch Ball SHK94RR

Question

Question:

Sticker on hitch in picture says 12000 lbs, but description says 20k?

asked by: Paul C

0

Expert Reply:

Good catch; I checked directly with the manufacturer and verified the weight capacity is 20,000 lbs for the Shocker Hitch XRC Cushioned Ball Mount - 2-5/16" Ball - 7-1/2" Drop # SHK94RR.

There was a previous rating of 12,000 lbs but the part changed and the 20,000 lb capacity is correct. So if you need up to that amount of capacity you can use the # SHK94RR, and I do recommend locking the ball mount as well as platform by using the InfiniteRule Locking Pins for Shocker Hitch Ball Mounts # IR39FR.

expert reply by: Kyle S

0

Answer 1

I spoke to my contact at Curt and he informed me that if you were to remove the factory hitch of your 2012 Dodge Ram you could install a Curt Trailer Hitch #13333 but you would have to leave the bumper beam installed on your truck though to complete…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 4

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 5

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 6

The correct replacement leaf spring bushings for any given trailer will be dependent on the width and type of the leaf springs. The most common for a Dexter 10,000 lb Trailer Axle are 3" wide slipper springs. If you have 3" wide slipper…

view full answer...

Answer 7

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

You can get a new brake mounting flange for your axle. The old flange will need to be cut off. The part is #4-44-1. This is designed to fit a 3 inch trailer axle and should be welded in place by a professional. Since you would also have to get the…

view full answer...

Answer 10

We do have 205/75R14 size radial tires that have a load range of D and a speed rating of at least 81 mph. Out of our available selection I recommend going with the Kenda Karrier #AM10235. This tire has a max load rating of 2,200 lbs at 75 psi and a…

view full answer...

Answer 11

In regards to the Correct Track Trailer Alignment and Lift Kit part #RR23QX, the kit provides a lift by essentially extending the hangers. This normally requires cutting off the old hangers and welding on new, taller ones but with this kit you…

view full answer...

Answer 12

The Correct Track Trailer Alignment and Lift Kit - Tandem Axle #RR23QX does come with all of the components needed to lift a tandem axle trailer. The center hangers of a tandem axle setup use different components than the front and rear hangers since…

view full answer...

Capacity of Shocker Hitch XRC Ball Mount With 2-5/16" Hitch Ball SHK94RR

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching