How To Find Replacement Bearing Kit For Trail Star Boat Trailer

Question

Question:

If I send you the VIN off my trail star boat trailer would you be able to see if you have a wheel bearing kit for it?

asked by: Jesse K

0

Expert Reply:

Vin numbers cannot be used to identify wheel bearing/axle information, as they're is no database for that. The OEM trailer manufacturer's use whatever axle they have on hand that day, so it could have a few different options.

Most boat trailers have 1 of 3 possible bearing combinations, but you'll need to measure your spindle to be sure.

The first is a 1" straight spindle that uses bearings # L44643 and measures 1" at bearing points on the below diagram, and uses seal # 34823 which measures 1.249" at the grease seal point on the spindle. Bearing kit with everything you need for (1) spindle is # BK1-100, you'll need (2) per axle.

Second option is a 1-1/16" straight spindle which uses bearings # L44649 and measures 1.063" at the bearing points, and uses seal # RG06-020 which measures 1.500" at the grease seal point on the spindle. Bearing kit for (1) spindle is # BK1-150, you'll need (2) per axle.

Last is 3,500lb axle tapered spindle which uses inner bearing # L68149 which measures 1.378" on the spindle, outer bearing # L44649 which measures 1.063" on the spindle, and grease seal # RG06-050 which measures 1.719" on the spindle. Bearing kit for (1) spindle is # BK2-100, you'll need (2) per axle.

These are all pretty exact measurements so you need to use digital calipers like # PTW80157.

expert reply by: Samuel C

0

Trailer Axle Spindle Diagram
(click to enlarge)

Answer 1

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 2

I really wish we had replacement parts still for the Atwood couplers but since they've been out of business for so long we don't have any way to get the parts you are wanting.

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 5

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 6

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 9

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

How To Find Replacement Bearing Kit For Trail Star Boat Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching