Trailer Hitch and Wiring Kit that Fits 2018 Chevy Equinox Diesel

Question

Question:

I have a 2018 equinox, but it’s the diesel engine. I’ve been looking to add a hitch and wiring for trailer lights, but I wanted to make sure I’m getting the right stuff first. For the hitch it’s part number 76217 and the wiring is 118750, is that correct?

asked by: Gabe

0

Expert Reply:

The Draw Tite hitch part # 76217 does fit the diesel models of your 2018 Chevy Equinox and so does the trailer wiring part # 118750 so do have the right stuff picked out.

expert reply by: Jameson C

0

Answer 1

Pressure treated lumber can be used for bunk boards along with bunk carpet like the #CE11349. However, it is possible that some corrosion may occur from the chemicals in the lumber over time. The CE Smith bunk boards like #CE27840 are made from…

view full answer...

Answer 2

I think the best option for your pontoon boat trailer would be to break the 18' long bunk boards down into three sections which then leaves 6' for each section. The shorter each board is, the more support you will have to a degree which is…

view full answer...

Answer 3

The CE Smith bunk boards, like part #CE27840, are made from untreated southern yellow pine. I confirmed this with CE Smith for you.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 9

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Trailer Hitch and Wiring Kit that Fits 2018 Chevy Equinox Diesel

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching