Will Curt Trailer Hitch Receiver Fit with Full Size Spare on a 2001 Ford Ranger

Question

Question:

my hitch arrives tommorrow was told my spre wuld mount back up after install hitch if u dont think it will i need to return it and get the hitch that will clear spare tire i purchased part # 13019 please reply asap thnks

asked by: George K

0

Expert Reply:

The Curt Trailer Hitch Receiver # 13019 will fit with the full size spare on your 2001 Ford Ranger so you have nothing to worry about!

I'm attaching a photo we took when we installed this hitch and we were able to get the full spare back in place. You might need to angle it or move it around a little to get it back in the resting spot but it will definitely fit.

expert reply by: Jon G

0

Full Size Spare Fit with Curt Trailer Hitch on Ford Ranger
(click to enlarge)

Answer 1

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way…

view full answer...

Answer 4

Hey Roy, The only U-bolt kit we currently only offer for 1-1/2" square axles is part #CE23102, which only has a 3-3/8" length so it likely wouldn't be the best option for you. Instead you'll want to order the…

view full answer...

Answer 5

The Curt hitch that fits your 2008 Ford Ranger part #13019 fits with a full size spare. I attached a picture that shows the hitch installed along with a full sized spare.

view full answer...

Answer 6

The difference between the Curt Class III Receiver Hitch part #13019 and the Curt Class III Receiver Hitch part #13138 is strictly aesthetics. The square tube option is a bit more cost effective and it matches the body lines on your 1992 Ford…

view full answer...

Answer 7

It is difficult to identify what hitch fits just by looking at the holes in the frame. However, I can tell you that the Curt Trailer Hitch Receiver #13138 is confirmed to fit your 2004 Ford Ranger Edge. This is a Class III hitch with a 2"…

view full answer...

Answer 8

As far as the mounting bracket, you can absolutely screw it directly to the hitch if you want. We do this frequently in our own installs and it will not compromise the strength of the hitch in any way. Now putting a few holes in the hitch does open…

view full answer...

Answer 9

I went out o the warehouse to measure the Hollywood Racks Sport Rider SE2, #HR1450Z. From the end of the shank to the nearest part of the elongated pin hole it measures 1-3/8 inches. From the end to the center of the hole it is 2-3/4 inches. And from…

view full answer...

Answer 10

The Hollywood Racks part #HR1450Z is incredibly stable. While it may not look as sleek as some of the more expensive racks it actually performs better in terms of stability than nearly all of them. Actually the rack doesn't move at all so…

view full answer...

Will Curt Trailer Hitch Receiver Fit with Full Size Spare on a 2001 Ford Ranger

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching