Trailer Hitch for 2008 Ford Ranger that Allows Full Size Spare

Question

Question:

Just wanted to know what hitches will work with a full size spare. 2008 Ford Ranger

asked by: Scott W

0

Expert Reply:

The Curt hitch that fits your 2008 Ford Ranger part # 13019 fits with a full size spare. I attached a picture that shows the hitch installed along with a full sized spare.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The difference between the Curt Class III Receiver Hitch part #13019 and the Curt Class III Receiver Hitch part #13138 is strictly aesthetics. The square tube option is a bit more cost effective and it matches the body lines on your 1992 Ford Ranger…

view full answer...

Answer 2

Thank you for the photo that was helpful; on some models of Ranger drilling is required, but based on your photo, you will not have to drill in order to install the Draw-Tite hitch you asked about, which is the following part number: - Draw-Tite…

view full answer...

Answer 3

To install the Draw-Tite Class III 2 Inch Hitch, part #75082, on your 1996 Ford Ranger you do not need to completely remove the bumper. The bumper is held on to the vehicles frame by two bolts on each side of the vehicle. When installing the…

view full answer...

Answer 4

There are both Class I and Class III trailer hitches available that are confirmed to fit your 2010 Honda CR-V. The available Class I hitches, such as the Draw-Tite Sport Frame #24792, feature a square tube design, while the Class III hitches like the…

view full answer...

Answer 5

It is difficult to identify what hitch fits just by looking at the holes in the frame. However, I can tell you that the Curt Trailer Hitch Receiver #13138 is confirmed to fit your 2004 Ford Ranger Edge. This is a Class III hitch with a 2"…

view full answer...

Answer 6

That is a great question. There are three Class III trailer hitches available that are confirmed to fit your 2018 Honda CR-V. As you mentioned, the etrailer.com #e98848 and the Curt #C13397 both feature a square crosstube while the Draw-Tite #76128…

view full answer...

Answer 7

According to my contacts at Curt Manufacturing, Ranger models manufactured after the 1997 model year will not have any spare tire clearance issues. You might find that temporarily removing the spare during the install will allow more working room. I…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

I'm not 100% sure what size tire came on your 2006 Ford Ranger but if the 245/75R16 spare you have is the stock tire then you won't have any problems with the Curt Trailer Hitch Receiver #13138 installed. We did have a customer send in a…

view full answer...

Answer 10

No the curt is a great fit. Your spare tire will fit right back in its original position after installing the Curt Trailer Hitch Receiver Class III part #13138 . I have included a photo of it installed for you to reference hoe it fit with the spare.…

view full answer...

Answer 11

I spoke with my contact at Curt and he provided a picture to show what to look for when it comes to determining whether your 2000 Ford Ranger has the front crossmember. You will see his picture off to the right. If your Ranger DOES NOT have a…

view full answer...

Answer 12

To get replacement mounting hardware for the Curt #13019 trailer hitch on your 2001 Ford Ranger you will need part #RHK. Simply go to the product page and select "Curt" from the drop-down manufacturers menu and then input "13019"…

view full answer...

Trailer Hitch for 2008 Ford Ranger that Allows Full Size Spare

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching