Mounting Holes Pattern of Round Snap Ring Swivel Jack

Question

Question:

Im planning on removing the snap ring plate and pull pin to mount Item # TJB-2002S-B with bolts. Can you please provide me with the hole pattern so I know where to put the holes? Could you also provide me with the dimensions of the head of this jack? Thanks

asked by: Shawn N

0

Expert Reply:

The mounting holes are 3 inches apart on center for the Round Snap Ring Swivel Jack w/ Footplate - Weld On - Sidewind - 14-1/2" Travel - 2,000 lbs # TJB-2002S-B.

The head is 2-1/2 inches square for this jack as well.

expert reply by: Kyle S

0

Answer 1

From previous customers who have tried it we know that the Fulton jack #FTJ120W0301 fits the exact same mount as the Shelby jack so this would be your best option.

view full answer...

Answer 2

Yes, you can use stainless steel (heavy-duty) staples to attach boat trailer bunk board carpet like CE Smith #CE11372 to pressure treated wood. You can also use hot-dipped galvanized staples. Either type is fine for use with treated lumber.

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 4

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 7

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 8

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 9

For all intents and purposes, yes, the Fulton drop leg stabilizer jack SJL80300 is the same as the square leg jack you asked about: - Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs #SJ-R208 Different manufacturers but otherwise they…

view full answer...

Answer 10

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 11

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 12

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Mounting Holes Pattern of Round Snap Ring Swivel Jack

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching