Dimensions of T-Bolt In The Brophy Camper Tie-Downs # BR2007

Question

Question:

I need dimensions of Item # BR2007 to ensure I can use this part. Thank you,

asked by: Allen D

0

Expert Reply:

The T-Bolt # BR2007 has a 3" long by 3/4" wide and 3/16" thick steel plate welded to a 4" threaded rod.

expert reply by: Bud M

0

Answer 1

The Brophy Clamp On Camper Tie-Downs #HSSF will have a very slight amount of play since there is a compressible pad to prevent scratches on the bedrails, but it sounds like you're having much more significant play. I've attached a picture…

view full answer...

Answer 2

I confirmed with Brophy that the length of the Replacement T-Bolt for Brophy Camper Tie-Downs #BR2007 is 6 inches long.

view full answer...

Answer 3

To install a brake controller on your 2017 Chevrolet Silverado 1500 LT 4x4, you will just need the vehicle specific plug-in adapter. These adapters are usually brand specific. For example, if you go with the Tekonsha Prodigy P3 brake controller,…

view full answer...

Answer 4

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 5

The primary advantage of frame-mounted camper tie-downs like the TorkLift #TLF2012A and #TLF3001A, which are designed to fit your Ford F-350 if it has the 6-3/4 foot bed without a step/board underneath and a factory hitch, is the stability they…

view full answer...

Answer 6

I spoke with my contact at Brophy and they stated you'll be fine using the Brophy Clamp On Camper Tie-Downs - Bed Mount - Black Powder Coated Steel - Qty 4 Item #HSWB as long as the railing on the back of your 2008 Chevy Silverado isn't over…

view full answer...

Answer 7

The Trimax King Pin Lock #TMX56RR can still be used with your 5th wheel having a capture plate from PullRite. The capture plate mounts to the top of the kingpin and only takes up a similar amount of space that a Lube Plate #RP83002 would. If you…

view full answer...

Answer 8

According to CR Brophy, the camper tie down brackets you'd looked at, part #HSWB are specifically designed to fit the bed of a 2019 Ford F-250 and 350. There does indeed need to be 2 inches of available space under the lip of the truck bed side…

view full answer...

Answer 9

Yes, the Brophy camper tie downs like the #HSAB can be used with bed rail covers. If you check out the picture I attached you can see a set installed on a bed rail with plastic covers.

view full answer...

Answer 10

We have spoken with Brophy in the past and for a Ford F-150 with aluminum body such as your 2017 model they recommend using the Brophy Clamp On Camper Tie-Downs part #HSSF. There won't be any issues with these tie downs and an aluminum bed so…

view full answer...

Answer 11

The Brophy Slide In Camper Tie-Downs #HSAB might be a fit for your 2011 Ford F-150 but you'll need to do a bit of measuring first and you'll likely need to trim out holes where the tie-downs would sit. You'll want to verify that #HSAB…

view full answer...

Answer 12

There is no weight capacity for the Brophy Clamp On Camper Tie-Downs #HSSF. The tie-down hardware kit #TDHP, that is used to secure the camper to the #HSSF tie-downs has a weight capacity of 3,000-lbs. My contact at Brophy said the tie-downs will…

view full answer...

Dimensions of T-Bolt In The Brophy Camper Tie-Downs # BR2007

Product Page this Question was Asked From

Continue Researching