What is the Length of the Replacement T-Bolt for Camper Tie-Downs # BR2007?

Question

Question:

What is the length on item 2007?

asked by: Phil M

0

Expert Reply:

I confirmed with Brophy that the length of the Replacement T-Bolt for Brophy Camper Tie-Downs # BR2007 is 6 inches long.

expert reply by: Bob C

0

Answer 1

The Brophy Clamp On Camper Tie-Downs #HSSF will have a very slight amount of play since there is a compressible pad to prevent scratches on the bedrails, but it sounds like you're having much more significant play. I've attached a picture…

view full answer...

Answer 2

The T-Bolt #BR2007 has a 3" long by 3/4" wide and 3/16" thick steel plate welded to a 4" threaded rod.

view full answer...

Answer 3

We do have a replacement T-bolt available for the Brophy Camper Tie-Downs part #HSAB, part #HSBP, part #HSCP, part #HSSF or part #HSWB. The replacement T-Bolts are part #BR2007 and only come in a pack of four. I have attached an installation video of…

view full answer...

Answer 4

The reason the manufacturers of the Brophy Clamp On Camper Tie-Downs - Bed Mount - Black Powder Coated Steel - Qty 4 Item #HSAB have the plastic bed rail exemption is because depending on the thickness of the plastic bed rail you might not have…

view full answer...

Answer 5

Yes, the Brophy camper tie downs like the #HSAB can be used with bed rail covers. If you check out the picture I attached you can see a set installed on a bed rail with plastic covers.

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 8

Hey James, The correct rear camper tie-downs to go along with your new TorkLift SuperHitch Original Trailer Hitch Receiver #TLD1102 are going to be part #TLR3505. These will mount directly to the hitch at the end of the crosstube.

view full answer...

Answer 9

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 10

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 11

Then I do have some good news for you Rick. The BAKFlip MX4 Hard Tonneau Cover #BAK448130 will not block the camera on your 2024 GMC Sierra 1500 Denali short bed truck. This is the correct cover for your truck not having the CarbonPro bed.

view full answer...

Answer 12

I do see the BAKFlip MX4 Hard Tonneau Cover #BAK52FR you found is for a short CarbonPro bed on your 2024 GMC Sierra 1500 Denali. This will interfere with the 3rd brake light bed camera on your truck. I recommend looking at the Pace Edwards…

view full answer...

What is the Length of the Replacement T-Bolt for Camper Tie-Downs # BR2007?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching