Replacement Frame/Chain Lift Brackets for Reese Weight Distribution System

Question

Question:

Looking for a Reese part for my Camloc WD. Broke towing yesterday. 25312YOT. Sheared off where chain attaches. Have pictures.

asked by: Billheybruck

0

Expert Reply:

It sounds like you might be looking for the snap-up brackets. In which case, you'd need the Replacement Snap-Up Bracket for Reese Weight Distribution Systems part # RP21501 (<600 lbs) or part # 58392 (>800 lbs). These brackets bolt to the frame and give you a spot to attach the chains from the spring bars. If this is not what you're looking for please send me a photo and I'd be glad to see if we have another option.

expert reply by: Conner L

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Hey Michael, thanks for reaching out! The Timbren Active Off-Road Bumpstops #T28GR you installed on your 2018 Ford F-150 unfortunately have that reputation among users (although Timbren claims their systems provide a smooth ride). Because of this we…

view full answer...

Answer 5

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 6

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 11

Yes, the Replacement Cover #PE48UV will indeed fit the 2018 Ford F-150 extended cab with the 67" bed. This is made to be a replacement cover for the Pace Edwards JackRabbit Retractable Hard Tonneau Cover #311-JRFA05A28 which is specifically for…

view full answer...

Answer 12

The 2" receiver for the EcoHitch item #EH87SR sticks out right through the middle of the air dam. I have attached a picture below that will show you what this front hitch looks like once installed. The EcoHitch Hidden Front Mount Trailer Hitch…

view full answer...