Replacement For T1401 Boat Trailer Winch

Question

Question:

I have the T1401 boat trailer winch that I want to replace I don’t see that winch on your website, what is the best replacement

asked by: Mike

0

Expert Reply:

The T1401 has been discontinued but based on my research that is a 1,400 lb winch with a 20 foot strap. To replace it, the best option is the very similar Fulton Trailer Winch # F142201.

The # F142201 is a 1,500 lb winch that also uses a 20 foot strap; you can use your current strap or a new one with part # DL24260.

expert reply by: Kyle S

0

Answer 1

The Fulton T1401 model has been discontinued. As a replacement I recommend the Fulton Single Speed Trailer Winch - 8" Long Handle - 1,500 lbs #F142201. The slightly smaller option is the Fulton Single Speed Winch - 8" Long Handle -…

view full answer...

Answer 2

The best way to determine the height needed is to measure from the top of your trailer frame to the top of the sides of your boat. If the 40" Tall Guide-Ons #CE27626 sit right at or slightly above the sides of your boat then the shorter…

view full answer...

Answer 3

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are…

view full answer...

Answer 4

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the…

view full answer...

Answer 5

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 6

A TPR roller like the #YR500YW-6P is going to be better than PVC. PVC is a cheaper product. TPR has the properties and performance of both PVC and rubber while having a higher tensile strength so it is going to be the most durable. I don't…

view full answer...

Answer 7

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Kevin, for your Demco DA70 actuator you can use the Reverse Lockout Solenoid for Demco Hydraulic Brake Actuators #DM11993.

view full answer...

Answer 11

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...