Do the Rhino-Rack RTC-Style Roof Rack Tracks Work with Thule Roof Racks

Question

Question:

Will this work with a Thule cross rack?

asked by: Casey T

0

Expert Reply:

If by cross rack you are talking about a roof rack with crossbars then the answer is no, the Rhino-Rack RTC-Style Roof Rack Tracks # RRRTC8JWMY11 will not work with a Thule cross rack. The Rhino-Rack RTC-Style Roof Rack Tracks # RRRTC8JWMY11 is compatible with Rhino-Rack RLTP, RLTF, RLT500, or RLT600 track-mounted legs like the # RRRLT600.

The Rhino-Rack Quick Mount Legs # RRRLT600 will let you use Rhino-Rack crossbars like the Rhino-Rack Vortex Aero Crossbars # RRVA118B-2.

I did not see a Thule option that was close to the 31-1/4" length of the Rhino-Rack RTC-Style Roof Rack Tracks # RRRTC8JWMY11. If you already have a Thule roof rack, please let me know. Also provide me with the year/make/model of your car and I can look further into this for you.

expert reply by: Scott S

0

Answer 1

I measured the widths of the c-channel on the Rhino Rack Vortex Aero Crossbars and the bottom width is 7/8 inches and the neck width is 7/16 inches. I have attached a photo showing these measurements for you to check out. As long as the t-bolts on…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Hey Jeremy, Typically with boat trailers the manufacturer will install hydraulic surge brakes because you don't have to worry about the water damaging wires like you would with electric brakes. That being said, if you use a heat shrink butt…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

There is a trailer hitch receiver as well as a 4-way wiring harness that fit your 2022 Jeep Grand Cherokee WL; that said, we don't have any way to reference a VIN so you'll need to confirm if you do have the WL, which is the new model of…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

Hey Gary, so the Yakima 54" Tracks for Roof Racks #Y26RR that you referenced are compatible with your setup as they provide the standard dimension roof tracks that your Sherpa Crows Nest was designed to fit. With that said the correct T-bolt…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...