Can Landing Gear be Used on Gooseneck Trailer
Question:
I have a sawmill trailer. It weighs between 2.5-3k lbs. It is a gooseneck. To use sawmill, trailer must be level. I was hoping to add two jacks to the rear 3K capacity each and a landing gear replacement on front to level my sawmill trailer. Currently gooseneck trailers landing gear isnt functioning. Could I use this Landing Gear in combo with two rear jacks to slightly lift and level my sawmill trailer? If so, which weld on jacks would you recommend for the rear of the trailer. Thanks
asked by: Jeff N
Expert Reply:
I don't see any reason why your gooseneck trailer can't use the Landing Gear Set # RVLG-8HDL. Then for rear jacks you can weld onto the frame, a sidewind jack would seem to be the best option, the Square Direct Weld Jack w/ Footplate - Drop Leg - Sidewind - 28-7/8" Lift - 7,000 lbs # TJD-7000S.
Products Referenced in This Question
Square Direct Weld Jack w/ Footplate - Drop Leg - Sidewind - 28-7/8" Lift - 7,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Fifth Wheel Trailer
- Gooseneck Trailer
- Utility Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 6001 - 7000 lbs
- Sidewind Jack
- 28-7/8 Inch Lift
- Weld-On
- With Rectangle Foot
- etrailer
more information >
Product Page this Question was Asked From
Landing Gear Set w/ Handle - 36-1/2" Lift - 8,000 lbs
- Camper Jacks
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 7001 - 8000 lbs
- Landing Gear
- Sidewind Jack
- 36 Inch Lift
- Weld-On
- 2 Jacks
- etrailer
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Square Direct Weld Jack w/ Footplate - Drop Leg - Topwind - 29" Lift - 7,000 lbs
- Video: etrailer Trailer Jack - Side Frame Mount Jack - TJDP-5000-FLB Review
- Shop: Landing Gear Set w/ Handle - 36-1/2" Lift - 8,000 lbs
- Shop: Square Pipe Mount Swivel Jack w/ Footplate - Weld On - Topwind - 15-1/2" Travel - 3,000 lbs
- Shop: Towing Mirrors
- Shop: Square Direct Weld Jack w/ Footplate - Drop Leg - Sidewind - 28-7/8" Lift - 7,000 lbs
- Q&A: Distance from Bottom Adjustment Hole to Bottom of Footplate on etraileer.com Replacement Drop Leg
- Q&A: Recommended Weld-On Trailer Jack with 15"+ of Travel
- Shop: Round Snap Ring Swivel Jack w/ Footplate - Weld On - Zinc - Topwind - 15-1/4" Travel - 2K
- Shop: Square Direct Weld Jack w/ Footplate - Drop Leg - Topwind - 29-1/4" Lift - 3,000 lbs
- Shop: Brake Controller
- Q&A: Tekonsha P3 Brake Controller 90195 Displays Message Output Shorted No Brakes
- Q&A: Diagnosing Overload Warning, No Brakes, On a Tekonsha Prodigy P3 Brake Controller
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: Choosing the Right Brake Controller
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Search Results: trailer jack
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Search Results: 25580
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: Trailer Wiring Diagrams
- Video: Choosing the Right Trailer Wiring
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: How to Choose the Right Trailer Hitch Class
- Video: etrailer Landing Gear Set Review
- Search Results: brake controller
- Shop: Suspension Enhancement
- Shop: Gooseneck Hitch
on Trailer Jack
