Recommended Replacement Jack For Shelby Bolt On Boat Trailer Jack

Question

Question:

Im looking for a boat trailer jack to replace my Shelby boat trailer jack. I dont have the model number. Im attaching photos

asked by: Miguel L

0

Expert Reply:

I recommend using the Xtreme Off-Road Swing-Up Trailer Jack # ORJW350D as we do not have a jack which will fit the same weld on bracket you have on your boat trailer. This jack can be bolted onto your frame and will allow you to have more adjustability than your current jack. It also has a dual wheel setup which will make it easier to mover around the trailer.

expert reply by: Bud M

0

Shelby Boat Trailer Jack
(click to enlarge)

Answer 1

The Extreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels, #ORJW350D has an overall length of 18".

view full answer...

Answer 2

Yes, the Extreme Off-Road Swing-Up Jack w/ Dual Wheels iItem #ORJW500D will work for your T@B 400 Tear Drop Trailer. It looks like your trailer comes with an a-frame jack. You would need to ensure you have enough space on your tongue to accommodate…

view full answer...

Answer 3

Yes, in order to set your trailer up for use with shore power you will first need an AC distribution panel. For this, I recommend a Progressive Dynamics Series AC Distribution Panel. In order to bring power into the panel you will also need a power…

view full answer...

Answer 4

We have the Dexstar Steel Spoke Trailer Wheel - 15" x 5" Rim - 5 on 4-1/2 - White Powder Coat, #AM20422. This is the Dexstar 5" 017-143-1X wheel. For a tire with a 2150 lb. load rating that fits this wheel, I suggest the…

view full answer...

Answer 5

Since heat rises I would at the very least put a set of the Trailer Vents #HMAV2-AVT2 near the top of the trailer to get the hottest air of the trailer out. What you could do for maximum air flow in your trailer is have a set facing forward in the…

view full answer...

Answer 6

The vents we offer for an enclosed trailer like part #9139 are designed to allow air into the trailer. None of the vents we offer create a pressurized condition in the trailer and none are equipped with an air filtration system to keep dust out.…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

A 4-way trailer connector will have four functions which means it will also have four wires for the exception of wishbone harnesses. These four functions are ground, tail light, right turn, and left turn. The ground function will usually be…

view full answer...

Answer 11

It really just depends on what the wires are for. Most likely you have several ground wires among the 8 as well as a couple running light circuits in there as well. You just have to run all of the wires to the correct circuits. The 4-way wiring of…

view full answer...

Answer 12

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Recommended Replacement Jack For Shelby Bolt On Boat Trailer Jack

Product Page this Question was Asked From

Continue Researching