What is Needed to Add Curt Brake Controller to 2010 Acura MDX

Question

Question:

Hello. I have a 2010 acura mdx with after market hitch and no wiring. I want to have a 7 pin RV connection and a 4 pin flat connection. Is getting a Curt C51110 brake controller and an etrailer ETBC7. Is that all I need?

asked by: Chris

0

Expert Reply:

You're on the right track; to add the Curt brake controller to your 2010 Acura MDX you'll need to add the 4-way as well as 7-way that comes with the # ETBC7. You will first install the 4-flat, which will activate your trailer's lighting functions, and you'll then plug that into the 7-way that comes with the # ETBC7, which also gives you the wiring, circuit breakers, and rest of the hardware needed for installation. The exact parts you need are the following:

- Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C56038

- Universal Installation Kit for Trailer Brake Controller # ETBC7

- Curt Venturer NEXT Trailer Brake Controller # C74VV

- Wiring Adapter for Curt Trailer Brake Controllers # C51515

expert reply by: Kyle S

0

Answer 1

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 5

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 6

The best brake controller option to go with is one that activates the brakes proportionally instead of time delayed. A proportional brake controller will activate the trailer brakes at the same time and with the same intensity as the tow vehicle…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 9

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

For your 2024 Hyunda Santa Cruz we have the Curt 7-way kit part #C68JR that is a confirmed fit. This installs by plugging into a factory wiring connector on your vehicle which means a really easy install that doesn't require any splicing.

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

What is Needed to Add Curt Brake Controller to 2010 Acura MDX

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching