Replacement for Oil Seal POS1501925TB

Question

Question:

Looking for grease seal, my part # POS1501925TB for 4x8 trailer: 1.98 OD X 1.49 iD

asked by: Mack E

1

Helpful Expert Reply:

The Seal POS1501925TB is for oil and it has an inner diameter of 1.5" and an outer diameter of 1.987". We don't have an oil seal in this size but we do have a grease seal, the Grease Seal part # 10-9 which measures 1.500" inner diameter x 1.987" outer diameter.

expert reply by: Conner L

1

Answer 1

The Redline Grease Seal item #10-42 is going to be the closest seal we have to your measurements of 2.335 OD and 1.789 ID. The .03 difference could be caused by a measuring issue like your caliper being off by a small amount. If not the seal has…

view full answer...

Answer 2

The seal number you mentioned does not match anything we carry or any of the cross-references we are aware of. You are going to have to take a couple measurements to determine which seal you'd need. To pick out a replacement grease seal you…

view full answer...

Answer 3

I was not able to find confirmed dimensions for the seal part 16192TC but we do have many grease seals and it is possible to find a replacement based on the dimensions. The seal inner diameter corresponds to the diameter of the spindle; the outer…

view full answer...

Answer 4

We do not carry a tool that will help install your races, though I can pass on some information for you that might be helpful. To install your races, this is what you'll want to do, according to our help article on replacing bearings, races and…

view full answer...

Answer 5

The #168233 Double Lip Grease Seal has an outside diameter of 2.332 inches and an inside diameter of 1.688 inches. This seal is not compatible with a AF2527E seal with a O.D 2.312, because, even though the O.D. id very close, the inner diameter of…

view full answer...

Answer 6

Instead of a castle nut and a cotter pin, your Ez-Lube spindle used a D-washer and a nut retainer. After the bearings are repacked and the grease seal is in place, working the hub gently into place until it seats fully. Install the D-washer then the…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Replacement for Oil Seal POS1501925TB

Product Page this Question was Asked From

Continue Researching