Recommended Square Manual Jack Rated for at Least 19K

Question

Question:

Do you offer a square, manual jack capable of lifting 19k lb?

asked by: Cliff G

1

Helpful Expert Reply:

We have some square jacks for higher weight ratings for sure. None of them are rated for 19K specifically so the closest ratings are our 25K square jacks:

- Square 2-Speed Jack # TJD2SP-25100
- Square Jack # TJD-25100 (if you need a second jack)

This jack has 2 different speeds (1" every 34-1/2 turns OR 1" for every 4-1/2 turns) for different applications and it offers up to 13" of travel. When it's retracted the jack is 30" tall and when extended the jack is 43" tall.

Attached are some review videos for you to check out.

expert reply by: Jon G

1

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

Your current Greystone Fireplace WF2613R is a 26 inch wide curved fireplace which can easily be replaced with the Greystone 26" Electric Fireplace with Crystals - Recessed Mount #324-000069 as this is the same size. Install would not be…

view full answer...

Answer 9

Hey Philip so while we don't carry the exact spring you are looking for it does match the specs of the #e59SR so this would be a great solution. It's correct length at 23-1/8 inches and is for a 3,500 lb trailer axle like you have as well.

view full answer...

Answer 10

The part number 072-097-00 is for a Dexter leaf spring. Our closest equivalent would be the 5-Leaf Double-Eye Spring item #e34SR. This is a 3,000 lbs spring that works with 6,000 lbs axles. It measures 25-1/4" long from eye hole to eye hole.…

view full answer...

Answer 11

Yes, in order to use the Square 2-Speed Jack w/ Crank part #TJD2SP-12000SP-F in tandem you would need to obtain the correct follow leg which is the Square Direct Weld Jack part #TJD-12000SP-F2. The handle for this follow leg can be discarded as you…

view full answer...

Answer 12

I attached a picture I got from Buyers Products that has the dimensions of the Buyers Products Hook and Keeper for Enclosed Trailer Door #BP64FR that has the dimensions you are looking for.

view full answer...