Replacement Brake Assembly Set for Lippert LH 296651 RH 296652

Question

Question:

I have contacted Lippert for brake assembly kits to fit axle on my 5th wheel, they gave me their part numbers as listed below. Do you carry lippert and alternative brands. Will need Qty of 2 Each Self-Adjusting LH 296651 RH 296652

asked by: Terry G

0

Expert Reply:

I did some digging and it looks like the brake assemblies you need are 12 inch by 2 inch and for up to 7k axles so for that you'd want the part # AKEBRK-7-SA which is a self adjusting set of assemblies that matches that.

expert reply by: Jameson C

0

Answer 1

The two Dexter hub and drums you mentioned do fit the same spindle as they use the same bearings and grease seal, but they have different capacities, and I verified with Dexter that the actual drum itself is different to compensate for the…

view full answer...

Answer 2

The correct braking assembly kit for a Dexter 4,000 Lb Axle is the Dexter Electric Trailer Brake Kit part #K23-462-463-00 for manual adjust or Dexter Nev-R-Adjust Electric Trailer Brake Kit part #K23-478-479 for self-adjust. These are almost the same…

view full answer...

Answer 3

I have just what you need. The Lippert 4,000 Lb Axle on a 2017 Gulf Stream Vintage Cruiser 19ERD uses all the same parts as a 3,500 lb axle so the etrailer Trailer Hub and Drum Assembly part #AKHD-545-35-EZ-K would be the correct replacement.

view full answer...

Answer 4

The correct hub/drum for a Dexter 4,000 Lb Axle is the Dexter Trailer Hub and Drum Assembly part #K08-426-91. Then for the brakes, you can use the Dexter Nev-R-Adjust Electric Trailer Brake Kit part #23-468-469. The hubs/drums for a 3,500 lb axle are…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 8

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 9

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 10

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...

Answer 11

The Trailer Hub and Drum Assembly part #AKHD-545-35-EZ-K would be an excellent replacement for a Tru-Ryde Hub/Drum RVD-H-545. Then for new brakes, I recommend the Hydraulic Trailer Brake Kit part #AKFBBRK-35.

view full answer...

Answer 12

We do have what you need to replace the UFP HD-1377-10 hub and drum as well as add hydraulic brakes for your boat trailer. Here are the exact parts you will need: - Dexter Trailer Hub and Drum Assembly #84546UC3 - Hydraulic Trailer Brake Kit -…

view full answer...

Replacement Brake Assembly Set for Lippert LH 296651 RH 296652

Product Page this Question was Asked From

Continue Researching