Recommended 2 Inch Lift for Keystone Cougar Half-Ton 29RKS

Question

Question:

My trailer when hitched to the truck sits nose high. I would like to raise my trailer up about 2 inches. Is there a way to achieve this. I was thinking of adding two inch blocks to the axels. I am open to options. Thanks

asked by: Gib D

0

Expert Reply:

The closest thing we have to a 2" lift would be the Correct Track Trailer Alignment and Lift Kit # RR23QX. This kit can raise your trailer by 1-1/4" or 2-1/4" and will also keep your axles properly aligned. This would also mean you need the MORryde Suspension Upgrade Kit for Tandem Axle Trailers w Correct Track # MR58ZR instead of the # MR46ZR you ordered.

The other option to lift your trailer is with an over-under conversion kit. This would flip your axles, raising your trailer by the axle diametern and the height of the leaf spring stack. The correct kit depends on the diameter of your current axles. For a 2-3/8" axle you need the # K71-384-00 and for a 3" axle the # K71-385-00. You will need a kit for each axle. This will raise it a little higher, but also help save some money.

I have attached some installation videos for your reference.

expert reply by: Robin H

0

Answer 1

The ID and Password you need to link your Lippert Ground Control 3.0 item #LC675817 system to the app on your phone can be found on the gateway inside your 2021 Cougar 290RLS. You have the antenna to connect wirelessly but if you don't have…

view full answer...

Answer 2

The trailer lift kit options really come down to the axle type and setup. For leaf spring axles, you can either flip the axles with a kit like part #K71-384-00 or part #K71-385-00 or you can raise the hangers/shackles with a kit like part…

view full answer...

Answer 3

Congrats on the new truck! There are a couple of options to lift your 2020 Montana High County depending on if your axle's sit above or below the leaf springs. If your axles are already below your leaf springs the only option is the Correct…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 6

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 7

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

Answer 8

Hey Kevin thanks for your question. There is not much downside to going with the 5,000 lb springs instead of the 3,500 lb. A higher rated spring may make the ride a bit more "chunky" at times, since the spring would not flex as easily.…

view full answer...

Answer 9

Yes, going from a 4 leaf to a 6 leaf spring would add slightly to your ride height. For example, if the current 4 leaf spring has 3/8" thick leaves, and you go to a 6 leaf spring with 3/8" thick leaves, you would be adding 3/4" of…

view full answer...

Answer 10

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but they…

view full answer...

Recommended 2 Inch Lift for Keystone Cougar Half-Ton 29RKS

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching