Replacement Spring For Dexter Double Eye Leaf Spring 072-097-02

Question

Question:

Do you have a replacement leaf spring for Dexter D52 axle with leaf spring 072-097-02?

asked by: Aaron K

0

Expert Reply:

The 6-Leaf Double-Eye Spring # e94SR will work as a replacement for your Dexter 072-097-02 leaf spring. You Dexter spring is the same 26" length as ours but ours will have 6-leaves versus the 4 on your Dexter spring.

expert reply by: Bud M

0

Answer 1

Your current Dexter springs 072-097-00 are a 25-1/4 inch leaf spring that is rated for 5,200 lbs. So we have a couple options that would match the length but not the exact capacity. You'd want the part #e28SR for a 5k rated spring in this…

view full answer...

Answer 2

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is…

view full answer...

Answer 5

The AllTrek 4000 kits provide the best cushioning so if you were to upgrade from your CRE3000 kit to the Alltrek you would see a big improvement. If you have a 35 inch wheelbase you'd want the part #MR29DR or if you have a 33 inch wheelbase…

view full answer...

Answer 6

The absolute best cushioned equalizer that fits the dimensions you mentioned having would be the MORryde ALLTREK 4000 part #MR89DR as this is only option to provide vertical and horizontal cushioning. This would make a big difference and you'd be…

view full answer...

Answer 7

You will measure the MORryde Suspension Upgrade Kit for Tandem Axle Trailers #MR76ZR from the center of each hole on the shackle strap.

view full answer...

Answer 8

Yes, going from a 4 leaf to a 6 leaf spring would add slightly to your ride height. For example, if the current 4 leaf spring has 3/8" thick leaves, and you go to a 6 leaf spring with 3/8" thick leaves, you would be adding 3/4" of…

view full answer...

Answer 9

The hangers you currently have on your trailer are ones I have run into before. That being said, I spoke with MORryde and the #MR27ZR will still fit your trailer, but there is a modification that will need to be made. You’ll have to trim according to…

view full answer...

Answer 10

Yes, the MORryde Suspension Upgrade Kit for Tandem Axle Trailers - 3-1/8" Long Shackle Straps #MR76ZR will fit with the Equa-Flex system on your Grand Design.

view full answer...

Answer 11

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 12

Hey Patrick, so for your leaf spring upgrade I am going to need to know a couple of things before I can get you over to the right part. Specifically, the length from eye to eye, the spring width, leaf thickness, and the number of leaves. From here I…

view full answer...

Replacement Spring For Dexter Double Eye Leaf Spring 072-097-02

Product Page this Question was Asked From

Continue Researching