Replacement 12" Brakes Assemblies And Hubs For ALKO/Hayes Trailer Axle

Question

Question:

HELLO FROM THE BEST I CAN TELL THE NUMBER ON THE BACK OF THE HUB IS KAE 96002-02L. IT IS A 12X2 HUB WITH 4 BOLT PATTERN AND 8 LUG 1\2 X 20. IT HAS A 31\2inch CENTER HOLE FROM THE MEASUREMEN I SEND TO YOU. I THINK THIS IS AN OLD DEXTER AXLE BUT NO INFORMATION ON THE AXLE ITSELF. I LOOKING TO REPLACE ALL 4 COMPLETE. CAN YOU TELL ME WHAT I NEED TO GET THE DONE?

asked by: DONALD W

0

Expert Reply:

Based on the mounting bolt hole spread you have an older ALKO/Hayes axle. For this we have the Left # 23-105-09 and Right # 23-106-09 brake assemblies. These brake assemblies have both the Dexter 5 bolt and ALKO/Hayes 4 bolt mounting patterns for the brake assemblies.

To verify the correct hub you will need to measure your spindle with a Digital Caliper # PTW80157. You will most likely need the Hub/Drum Assembly # AKHD-865-7-2-EZ-K which has a Grease Seal # GS-2250DL (2.25" ID), Inner Bearing # 25580 (1.75" ID) and Outer Bearing # 14125A (1.25" ID). I have included an image to show the measuring points for your spindle. Please let me know if you find any different measurements on your spindle.

expert reply by: Bud M

0

Spindle Measurement Points
(click to enlarge)

Brake Assembly Mounting Bolt Pattern
(click to enlarge)

Answer 1

Unfortunately, we do not have the 14” diameter x 2” wide braking assemblies you need for your trailer. I also did some searching online and could not find any replacement parts for you either. The only option I can offer you would be to replace with…

view full answer...

Answer 2

Kelsey is related to Hayes/AL-KO. We do have assemblies that may possibly fit but you will need to measure the center to center distance between the 4 bolt pattern on the brake mounting flange. On our brake assemblies that may fit, #23-105-09, and…

view full answer...

Answer 3

The Dexter Electric Brake Kit #23-105-106-09 is currently the only 12" brake kit we carry which utilizes the 4 bolt flange for the Kelsey Hayes axles. It was created with the 5 bolt pattern as well so that it could be used for more than just the…

view full answer...

Answer 4

If you have a larger wheel size currently than 16 inch on your trailer axle that has 6k axles the install of the Dexter Electric Brake Kit for 4 Bolt or 5 Bolt Flange - 12" #23-105-106-09 would fit and work great. This would not cause there to…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

The replacement antenna for the Voyager WiSight Wireless RV Backup Camera Monitor #WVOM541AP is part #VO54FR on our site. If you're looking for the replacement antenna for the camera #WVCMS130AP instead then that would be part #PXXHD0006301R that…

view full answer...

Answer 7

Based on the information you have given me, you have a 3,500 lb axle that is 84" long (hub face to hub face) with a 70" spring center length. At this time we do not have any replacement axles that are 84" long, but I do have a…

view full answer...

Replacement 12" Brakes Assemblies And Hubs For ALKO/Hayes Trailer Axle

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching