Distance From Bottom of Wheel to the Top of the Bottom Plate of Ultra-Fab Skid Wheel # UF48-979014

Question

Question:

What is the height of the wheel from bottom of the wheel to where the bottom plate should be?

asked by: Bill M

0

Expert Reply:

I went out into our warehouse and pulled a set of the Ultra-Fab Rotating, Hitch Mounted Skid Wheels # UF48-979014 and found that the distance from the bottom of the wheel to where the bottom plate will be is 5-3/4 inches.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Ultra-Fab Hitch Mounted Skid Wheels for RVs up to 30' Long - 4" Diameter - Qty 2 #UF48-979015 is not suitable according to the manufacturer. I recommend the Roadmaster Rollaway Trailer Hitch Protector #RM-050 as an option for…

view full answer...

Answer 2

The longer the RV, and the greater the distance between the rear of the RV and the back axle, the greater the forces the skid wheels will have to deal with. This is why the larger, stronger skid wheel those used on the Ultra-Fab #UF48-979013 are…

view full answer...

Answer 3

Rollers like the Ultra-Fab Hitch Mounted Skid Wheels #UF48-979015 don't have specific weight limits since it would be hard to determine exactly how much weight would be on the rollers at any given time when they are use. Instead, they are…

view full answer...

Answer 4

This is a two fold answer according to my technical contact at Ultra-Fab. If you happen to be turning at the same time you are backing up then you will want to go with the caster type wheels #UF48-979011 that you referenced. I do want to mention that…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

I can certainly point you in the right direction. This will be a tricky one, as the Dexter 5,200 lb axles can use more than one seal size. We do not have the ability to pull an OEM build sheets to see what parts they installed at the factory so we…

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

You can absolutely upgrade your manual electric trailer brake assemblies on your tandem axle trailer to self-adjusting brakes like the 10 inch #AKEBRK-35-SA or the 12 inch #AKEBRK-7-SA. As long as the assemblies on each axle match you can update your…

view full answer...

Distance From Bottom of Wheel to the Top of the Bottom Plate of Ultra-Fab Skid Wheel # UF48-979014

Product Page this Question was Asked From

Continue Researching