Can You Swap Out A Chevy/GMC Puck System Companion Base For A Ford Puck System Base

Question

Question:

I have a BandW Companion slider hitch out of a 2022 Chevy 3500. I just bout a 2022 Ford F450, both trucks used the puck system. I dont need a slider hitch anymore, but can the base unit be swapped out with a Ford puck system and still use the same head unit?

asked by: Greg C

0

Expert Reply:

Yes, you could swap out just the base with part # BWRVB3300 to get a fixed base compatible with the puck system in the bed of your F-450.

expert reply by: Kevin C

0

Answer 1

When adjusting the arms of the #BWRVK3305, you have the option of setting up so the king pin will sit 3 inches forward or 1 inch forward of the axle. I'd set it up at the tallest height, 18-3/4 inches above the floor of the truck bed and 1 inch…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 5

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 6

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 7

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 8

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 9

A wedge is needed, yes, and the Lippert Turning Point pin box does come with a universal wedge, but it is not a very good fit with the B&W Companion #BWRVK3710. So I highly recommend instead using the 5th Airborne Custom Wedge for B&W Fifth…

view full answer...

Answer 10

Hey Jay. It sounds like you are on the right track here because a sidewinder pin box will be your only option for pulling your 5th wheel since you have a short bed truck with the Rambox. That said, you are right that the Reese Sidewinder cannot be…

view full answer...

Answer 11

The recommendation for the 10" diameter lube plate on a B&W Companion 5th Wheel Trailer has come from the manufacturer of the fifth wheel hitch, B&W. The Lube Plate for Reese 5th Wheel Trailer Hitches part #RP83002 will work just fine…

view full answer...

Answer 12

The B&W Companion OEM 5th Wheel Hitch w/ Slider for Chevy/GMC Towing Prep Package #BWRVK3775 you're looking at will work fine with your new Chevrolet Silverado. This hitch has 3 height adjustments so you'll be able to set the hitch height…

view full answer...

Can You Swap Out A Chevy/GMC Puck System Companion Base For A Ford Puck System Base

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching