Recommended Front Mounted Hitch for a 2009 GMC Sierra 3500 Dually

Question

Question:

Does this fit my 2009 GMC Sierra 3500 dually?

asked by: Doug

0

Expert Reply:

Yes, the Curt Front Mounted Hitch item # 31109 does fit the dually models of the 2009 GMC Sierra 3500. This hitch is custom fit and bolts to your GMC with included hardware.

expert reply by: Jerred H

0

Answer 1

For your 2010 Chevy Silverado Super Duty truck, the Curt Front Mounted Trailer Hitch Receiver #31109 is a confirmed fit. The ground clearance will be dependent on your wheel size and your suspension. I reached out to my tech contact at Curt and…

view full answer...

Answer 2

You are correct, the Curt Front Mount Hitch for the 2010 GMC Sierra, #31109, does not require trimming for installation. I have provided a link to installation instructions and a video installation that you should find helpful. I have also linked a…

view full answer...

Answer 3

Due to the design of the front of your 2005 Chevy Silverado 3500 the only place you'll be able to have a front hitch opening is below the front fascia like where the Curt #31108 installs. This would be best option we have, but if you really…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

I have a solution for you. Here at Etrailer, we strongly discourage using wheel-mounted bike racks like the Kuat NV 2.0 #NV22B for bikes with fenders. Mounting wheels with fenders can cause the fenders to crack or become damaged, especially with the…

view full answer...

Answer 11

Yes, it does. The Hollywood Racks LED Light Bar item #HLY54RR is wired for a 4-way but comes with an adapter that will plug into a 7-way like yours to power the lights.

view full answer...

Answer 12

Yes, you can install a Curt Trailer Hitch Receiver #C11433 on your 2019 Chevrolet Spark. This receiver is capable of supporting up to 200lbs of tongue weight. With each of the Lectric 3.0 e-bikes weighing roughly 60lbs without the battery you will…

view full answer...