Replacement for Schwintek 170000 Slide-Out Motor

Question

Question:

Looking for replacement schwintek in wall slide motor 2019 grand design 337 rls reflection part # 170000

asked by: Byron K

1

Helpful Expert Reply:

Thanks for reaching out!

According to my research the Lippert In-Wall RV Slide-Out Motor # LC236575 is what you're looking for to replace your Schwintek 170000 slide-out motor.

expert reply by: Jon G

1

Answer 1

We have a Lippert Components replacement slide motor that will work with the Schwintek system. It is the Lippert In-Wall RV Slide-Out Motor #LC236575. It is a gear ratio of 300:1. This is the correct replacement for the Schwintek IG420294X00096R.

view full answer...

Answer 2

The floor slide out motor like #LC387523 is normally removed with just a socket wrench. Some motors are not separate from the gear assembly so you need to replace the entire assembly. Others have a separate gear box and the motor itself can be…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 5

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 6

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

The Replacement Amber Lens for MC32AB Trailer Lights #A32AB is a direct replacement for the SAE A P2 DOT 14 and would be what you'd need.

view full answer...

Answer 9

The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…

view full answer...

Answer 10

As far as height adjustability and weight capacities the Curt Q20 #C16130 and the Curt A20 #C16140 are identical. They both have a Gross Towing Weight of 20,000 lbs, a Vertical Load Limit of 5,000 lbs, and a height range of 13-17 inches. When it…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

Yes, the best option we can offer you to add fuel capacity is with the DeeZee Truck Bed Auxiliary Tank part #DZ91752X which should fit in the space you have between the cab and 5th wheel hitch no problem as it is only 9" deep. I don't have…

view full answer...

Replacement for Schwintek 170000 Slide-Out Motor

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching