Mounting Bracket Dimensions for the Cam-Action Lockable Door Latch w/ 36" Pipe for Enclosed Trailers

Question

Question:

What are the width and bolt hole center line dimensions for the bracket? See attached diagram.

asked by: Dan

1

Helpful Expert Reply:

Thanks for reaching out!

The width of the mounting bracket for the Cam-Action Lockable Door Latch w/ 36" Pipe for Enclosed Trailers # 305736 is 2-1/4" while the distance from the center of the mounting hole to the inner edge of the bracket is 1/2" (see attached photo).

I've also linked some review and installation videos for you to check out!

expert reply by: Jon G

1

Dimensions of Bracket for Cam-Action Lockable Door Latch
(click to enlarge)

Requested Dimensions for Cam-Action Lockable Door Latch Bracket
(click to enlarge)

Answer 1

Yes, if you like you can cut down the pipe of the Cam-Action Lockable Door Latch w/ 36" Pipe for Enclosed Trailers #305736.

view full answer...

Answer 2

For the barn door on your dump trailer, I recommend looking at the Cam-Action Lockable Door Latch Kit #383200. This is a nice steel cam-action door latch with a 1 inch wide hasp that can be installed flush on doors with a 3/4 inch offset. It…

view full answer...

Answer 3

I recommend part #PLR1904-Z. This is a barn door hinge for dump trucks and is made of 1/4 inch steel. I don't have a drawing or install instructions I can send you, but if you take these hinges to a qualified fabricator in your area he would…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

You're correct. The repalcement for your existing B12EA-22 brake would be #AKEBRK-7R-SA for the right side and #AKEBRK-7L-SA for the left.

view full answer...

Answer 11

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...