Recommended Bolts for the Channels of a Yakima LockNLoad Platform

Question

Question:

Will these bolts work with the T-Slots on the Yakima Lock n Load roof rack? I need to attach an awning mounting bracket.

asked by: Ken

0

Expert Reply:

I checked with Yakima and the correct bolts for LockNLoad Platform Racks like item # Y05045-39 are M8 T-Bolts like item # 853-0782.

The Replacement T-Bolt item # Y8880184 you were looking at are M10 bolts and wouldn't work.

Any extra length of the Replacement M8 T-Bolt # 853-0782 can be cut off.

expert reply by: Jerred H

0

Answer 1

I spoke with Yakima, and they informed me that the t-track on the Yakima LockNLoad Platform Rack for Crossbars #Y05045-39 measures 8mm (.31") high, and measures 11mm (.43") wide. Attached is a diagram of depicting these measurements for you…

view full answer...

Answer 2

It sounds like you're looking for the Replacement T-Bolt with Nut for Yakima Rack and Roll Trailers part #Y8880184 which are used to attach the towers to the frame.

view full answer...

Answer 3

You can use the Yakima LockNLoad Platform Rack On your A.R.E. HD MX Series Truck Cap. The mounting hardware wraps around your crossbars to secure it into place. If you have 2 crossbars on the roof, the largest platform you can put up there is…

view full answer...

Answer 4

If your spare tire has a 35" diameter then yes, the 60" Long x 54" Wide Yakima LockNLoad Platform Rack #Y05045-39 will have enough surface area for your tire. You can use the Spare Tire Carrier Kit #Y05032 to accomplish this. I looked…

view full answer...

Answer 5

The Antenna Mounting Bracket for Rhino-Rack Crossbars and Platforms #RR43196 does fit the channels of a Retrax XR tonneau and a Yakima Lock N Load platform like #Y05044-39. No other hardware is needed.

view full answer...

Answer 6

The Yakima Replacement Anchor Plate Style-A, Part #Y8810074, comes as a set of 8 plates that measure 3/4-inch x 7/8-inch. The centered threaded hole measures 0.2 inches (or 5.1 millimeters) in diameter. Please refer to the photo provided. The Yakima…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 10

For a roof rack to be compatible on your 2020 Jeep Wrangler with Sky One-Touch Power Top, it can't be mounted on the top of the roof and it needs to be high enough for the folding roof to clear. What you need are tall gutter-mounted roof racks.…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Recommended Bolts for the Channels of a Yakima LockNLoad Platform

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching