Dimensions of Yakima Anchor Plate A Part # Y8810074 and 60-Inch Track for Roof Racks
Question:
What are the dimensions of the A plates that come with the Landing Pad 1? Do you know the inside dimensions of the 60inch Yakima Track width/Ht.?
asked by: Jack
Expert Reply:
The Yakima Replacement Anchor Plate Style-A, Part # Y8810074, comes as a set of 8 plates that measure 3/4-inch x 7/8-inch. The centered threaded hole measures 0.2 inches (or 5.1 millimeters) in diameter. Please refer to the photo provided.
The Yakima 60-inch Track for Roof Racks, part # Y01135, is a set of two tracks with included hardware. I have indicated below the various measurements of the T-shaped channel within the track. The opening at the top of the track measures 0.45 inches wide; the top portion of the T measures 0.8 inches wide inside; the overall inside height of the T measures 0.25 inches; the base of the T measures 0.56 inches wide. A second photo shows the track cross-section with these dimensions indicated.
Products Referenced in This Question
Product Page this Question was Asked From
Replacement Anchor Plate "A" for Yakima LandingPad 1 (QTY 8)
- Accessories and Parts
- Roof Rack
- Tower Parts
- Pads
- Yakima
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Roof Rack
- Shop: Replacement Anchor Plate "A" for Yakima LandingPad 1 (QTY 8)
- Shop: Replacement T-Bolt with Nut for Yakima Rack and Roll Trailers - Qty 4
- Shop: Replacement Track Nut for Thule Tracker II Half Foot Pack or Tracker Fit Kits TK6, TK8, TK9
- Video: Rhino-Rack RTC-Style Roof Rack Tracks Review
- Video: Review of Yakima Replacement Anchor Plate "A" For LandingPad 1 - Y8810074
- Q&A: Can Yakima Roof Tracks Work with Sherpa Crows Nest
- Shop: Yakima 54" Tracks for Roof Racks
- Shop: Eye Bolts for Yakima HD Bar, JetStream, FlushBar, and RailBar Crossbars - 250 lbs - Qty 2
- Shop: Ladder Rack
- Shop: Yakima 60" HD Tracks for Roof Racks, OverHaul HD, and OutPost HD
- Q&A: Will Replacement Anchor Plate "A" for Yakima Landing Pad 1 Fit Yakima Rails on A.R.E. Camper
- Shop: Rhino-Rack Quick Mount Legs for Vortex Aero Crossbars - RTC and RT Roof Rack Tracks - Qty 2
- Shop: Trailer Hitch
- Search Results: yakima
- Shop: Brake Controller
- Search Results: roof track
- Q&A: Are Yakima Anchor Plates compatible With Rhino-Rack RTC-Style Roof Rack Tracks
- Shop: Trailer Wiring
- Q&A: Eye Bolt Anchor that Can Fit Into Yakima Roof Tracks
- Video: Yakima Crossbars Eye Bolts Review and Installation
- Search Results: yakima skyline
- Shop: Wheel Cover
- Shop: Suspension Enhancement
- Video: Review of Yakima Ladder Rack Parts - Replacement Hardware for Recovery Tracks - Y83FR
- Search Results: folding camper steps
- Video: Hopkins Trailer Breakaway Kit Review
- Video: Review of Progressive Dynamics RV Converters - Power Control Center AC/DC Panel Charger - PD4135K
- Q&A: Replacement for Magnetek 6612 Converter - 35A Progressive Dynamics RV Power Control Center
- Search Results: yakima 1a parts
K M.
4/30/2020
I have been looking every where for a t-nut that would fit a rhino rack RTC-16 track. I know this is specifically for Yakima, but would this work or is there some thing that would work that you could point me to? Thanks