Timbren 3,500LB Axle-Less System With 4 of Lift, Hydraulic Trailer Brakes and Wheels/Tires

Question

Question:

I’m looking for Timbren 3500k 4” lift with brake flange to allow for 5/4.5 pattern. The one listed doesn’t show the 5/4.5 as an option. I would like to buy these axles, the hydraulic brakes, and four 13” tires w/rims that are radial and rated around 1700#s if you could help me out. Thank you

asked by: Jared

0

Expert Reply:

We have the Timbren Axle-Less Trailer Suspension System # ASR3500S06 which has a 4" lift spindle with brake flange and will allow you to have a 5 on 4-1/2" bolt pattern. For the brakes we have either the Disc Kit # KOD59FR if you are wanting hydraulic disc brakes. Or you will need the Drum Brakes # AKFBBRK-35-D with 2 of the Hub/Drum Assemblies # AKHD-545-35-G-EZ-K per axle.

To get the weight rating you need for the tires you will want to step up to the Provider ST205/75R14 Radial Trailer Tire w/ 14" White Spoke Wheel # TA82MR. This tire is rated for 1,760lbs versus a 13" # AM31990 with the maximum load of 1,650lbs.

expert reply by: Bud M

0

Answer 1

It's very likely you have integrated hub/drums but the fact you have EZ lube spindles does not guarantee that is the case. You'll have to pull off a wheel and see or maybe you can see from the backside of the wheel. You will also need to know…

view full answer...

Answer 2

Best option would be the Timbren Axle Less kit part #ASR35HDS05 which has a 3,500 lb capacity and has a 4 inch lift built into it. It has brake flanges on the spindle already too so all you need to do is attach the hydraulic style of assemblies you…

view full answer...

Answer 3

It sounds like you are referring to surge brakes in which case I do have an option for you to add these to the Timbren Axle-Less Trailer Suspension System part #ASR1THDS03. In order to do this you will need the Demco Hydraulic Brake Kit part…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 9

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Timbren 3,500LB Axle-Less System With 4 of Lift, Hydraulic Trailer Brakes and Wheels/Tires

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching