Are the 30' Responsive Ratchet Self-Tensioning Tie-Down Straps Available in a Shorter Length

Question

Question:

Do the straps come in a shorter length or is it up to me to cut them down? I use straps to tie down my side x side and 30 ft. is way too long.

asked by: Bert J

0

Expert Reply:

If you are looking at this particular brand, then the 30' length of the Responsive Ratchet Self-Tensioning Tie-Down Straps # ST-2-2 is the only length that we have available.

If you are willing to look at a different manufacturer, we have the Titan Chain Ratchet Tie-Down Strap # TCLR21521-2. This strap has the same 3,333 lb. limit and 2" width, but this strap is 15' instead of 30'.

expert reply by: Scott S

0

Answer 1

So I went out to the warehouse and measured the stake pocket anchor #TL2B and from the lip to the top of the pin hole is right at 6-3/4". As long as your stake pocket is really only 6" deep these will work just fine for you.

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The spring hanger placement is going to be determined by your axle spacing. For example, if your axles are spaced 33 inches apart, as shown in the attached diagram, a 7K axle slipper spring, like #e74SR, requires a distance of 28-1/2 inches between…

view full answer...

Answer 4

I do have a great option for you, however we do not have any standard 3,500 pound round tube axles available that match the dimensions you provided. For an exact replacement your best option will be to go through a local trailer shop or the…

view full answer...

Answer 5

Many Curt products like their trailer hitch receivers are made in the USA. However, not all products are made here. To answer your question about the Curt Tow Strap Loop for 2" Hitches - 13,000 lbs #C45832 it is made overseas. I've linked…

view full answer...

Answer 6

When determining what rise/drop to use on a B&W Tow & Stow, it is important that your trailer connection is as level as possible. The first thing you need to do is measure the height of your hitch receiver from level ground to the top inner…

view full answer...

Answer 7

In order to keep a trailer from rolling on a slight incline, what you will need are wheel chocks. You will simply put them behind your trailer tires and that will prevent the trailer from rolling away from you. You'll want to get wheel chocks…

view full answer...

Answer 8

Trailer wheel lug nuts that are 1/2-inch inside diameter typically have a 20-TPI thread pitch (20 threads per inch). Most lug nuts also use a 60-degree-coned profile like #CE11051, but a 90-degree like #STN569 is also available for 9/16-inch studs.…

view full answer...

Answer 9

We measured the distance from the center of the hitch pin hole to the center of the hitch ball and found that measurements was 10-1/2 inches for the Curt Ball Mount for 2-1/2" Hitches #C45460. This ball mount has a 20,000 lb capacity and gives…

view full answer...

Answer 10

First, the DOT date code on a tire is 4 numbers. The first 2 are the week and the last 2 are the year. So for example if it was 2314 that means that tire was made in the 23rd week of 2014. There isn't a difference between a tire sitting on the…

view full answer...

Are the 30' Responsive Ratchet Self-Tensioning Tie-Down Straps Available in a Shorter Length

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching